--- 1/draft-ietf-dmm-distributed-mobility-anchoring-00.txt 2016-09-08 16:16:06.998841952 -0700 +++ 2/draft-ietf-dmm-distributed-mobility-anchoring-01.txt 2016-09-08 16:16:07.094844401 -0700 @@ -1,588 +1,1012 @@ -DMM H. Chan +DMM H. Chan, Ed. Internet-Draft X. Wei Intended status: Informational Huawei Technologies -Expires: March 2, 2017 J. Lee +Expires: March 12, 2017 J. Lee Sangmyung University S. Jeon Sungkyunkwan University + A. Petrescu + CEA, LIST F. Templin Boeing Research and Technology - August 29, 2016 + September 8, 2016 Distributed Mobility Anchoring - draft-ietf-dmm-distributed-mobility-anchoring-00 + draft-ietf-dmm-distributed-mobility-anchoring-01 Abstract - This document defines distributed mobility anchoring. Multiple - anchors and nodes are configured with appropriate mobility functions - and work together to enable mobility solutions. Example solution is - mid-session switching of the IP prefix anchor. Without ongoing - session requiring session continuity, a flow can be started or re- - started using the new IP prefix which is allocated from the new - network and is therefore anchored to the new network. With ongoing - session, the anchoring of the prior IP prefix may be relocated to the - new network to enable session continuity. + This document defines distributed mobility anchoring to meet diverse + mobility needs in 5G Wireless and beyond. Multiple anchors and nodes + with mobility functions work together to provide IP mobility support. + A network or network slice may be configured with distributed + mobility anchoring with the needed behaviors depending on the needs + of mobility support. In the distributed mobility anchoring + environment, multiple anchors are available for mid-session switching + of an IP prefix anchor. Without ongoing session requiring session + continuity, a flow can be re-started using a new IP prefix which is + allocated from the new network and is therefore anchored to the new + network. With ongoing session, the anchoring of the prior IP prefix + may be relocated to the new network to enable session continuity. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." - This Internet-Draft will expire on March 2, 2017. + This Internet-Draft will expire on March 12, 2017. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents - 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2. Conventions and Terminology . . . . . . . . . . . . . . . . . 3 - 3. Distributed anchoring . . . . . . . . . . . . . . . . . . . . 5 - 3.1. Distributed anchoring configurations . . . . . . . . . . 5 - 3.2. Distributed anchoring behaviors and message information - elements . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3.2.1. Location management behaviors and message information - elements . . . . . . . . . . . . . . . . . . . . . . 9 - 3.2.2. Forwarding management behaviors and message - information elements . . . . . . . . . . . . . . . . 10 - 4. Example mobility solutions with distributed anchoring . . . . 12 - 4.1. IP mobility support only when needed . . . . . . . . . . 12 - 4.1.1. Not needed: Changing to the new IP prefix/address . . 13 - 4.1.2. Needed: Providing IP mobility support . . . . . . . . 14 - 4.2. IP prefix/address anchor switching to the new network . . 16 - 4.2.1. Centralized control plane . . . . . . . . . . . . . . 17 - 4.2.2. Hierarchical network . . . . . . . . . . . . . . . . 20 - 4.2.3. Hierarchical network with anchoring change . . . . . 22 - 5. Security Considerations . . . . . . . . . . . . . . . . . . . 23 - 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 24 - 7. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 24 - 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 24 - 8.1. Normative References . . . . . . . . . . . . . . . . . . 24 - 8.2. Informative References . . . . . . . . . . . . . . . . . 26 - Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 26 + 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 + 2. Conventions and Terminology . . . . . . . . . . . . . . . . . 4 + 3. Distributed Mobility Anchoring . . . . . . . . . . . . . . . 6 + 3.1. Distributed Anchoring Configurations for Different + Networks or Network Slices . . . . . . . . . . . . . . . 6 + 3.1.1. Distributed Anchoring with Network-based Mobility + Support for Flat Network . . . . . . . . . . . . . . 7 + 3.1.2. Distributed Anchoring with Network-based Mobility + Support for Hierarchical Network . . . . . . . . . . 8 + 3.1.3. Distributed Anchoring for Host-based Mobility Support 11 + 3.2. Distributed Anchoring Behaviors and Mobility Message + Parameters . . . . . . . . . . . . . . . . . . . . . . . 13 + 3.2.1. Location Management Behaviors and Mobility Message + Parameters . . . . . . . . . . . . . . . . . . . . . 13 + 3.2.2. Forwarding Management Behaviors and Mobility Message + Parameters . . . . . . . . . . . . . . . . . . . . . 16 + 4. IP Mobility Handling in Distributed Anchoring Environments - + Mobility Support Only When Needed . . . . . . . . . . . . . . 21 + 4.1. No Need of IP Mobility: Changing to New IP Prefix/Address 22 + 4.1.1. Guidelines for IPv6 Nodes: Changing to New IP + Prefix/Address . . . . . . . . . . . . . . . . . . . 24 + 4.2. Need of IP Mobility . . . . . . . . . . . . . . . . . . . 26 + 4.2.1. Guidelines for IPv6 Nodes: Need of IP Mobility . . . 27 + 5. IP Mobility Handling in Distributed Anchoring Environments - + Anchor Switching to the New Network . . . . . . . . . . . . . 28 + 5.1. IP Prefix/Address Anchor Switching for Flat Network . . . 29 + 5.1.1. Guidelines for IPv6 Nodes: Switching Anchor for Flat + Network . . . . . . . . . . . . . . . . . . . . . . . 29 + 5.2. IP Prefix/Address Anchor Switching for Flat Network with + Centralized Control Plane . . . . . . . . . . . . . . . . 31 + 5.2.1. Additional Guidelines for IPv6 Nodes: Switching + Anchor with Centralized CP . . . . . . . . . . . . . 34 + 5.3. IP Prefix/Address Anchor Switching for Hierarchical + Network . . . . . . . . . . . . . . . . . . . . . . . . . 35 + 5.3.1. Additional Guidelines for IPv6 Nodes: No Anchoring + Change with Hierarchical Network . . . . . . . . . . 37 + 5.4. IP Prefix/Address Anchor Switching for Hierarchical + Network . . . . . . . . . . . . . . . . . . . . . . . . . 37 + 5.4.1. Additional Guidelines for IPv6 Nodes: Switching + Anchor with Hierarchical Network . . . . . . . . . . 39 + 6. Security Considerations . . . . . . . . . . . . . . . . . . . 39 + 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 39 + 8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 39 + 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 40 + 9.1. Normative References . . . . . . . . . . . . . . . . . . 40 + 9.2. Informative References . . . . . . . . . . . . . . . . . 42 + Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 42 1. Introduction A key requirement in distributed mobility management [RFC7333] is to - enable traffic to avoid traversing single mobility anchor far from - the optimal route. Distributed mobility management solutions do not - make use of centrally deployed mobility anchor + enable traffic to avoid traversing a single mobility anchor far from + an optimal route. Distributed mobility management solutions do not + make use of centrally deployed mobility anchor for the data plane [Paper-Distributed.Mobility]. As such, the traffic of a flow SHOULD be able to change from traversing one mobility anchor to traversing - another mobility anchor as the mobile node moves, or when changing + another mobility anchor as a mobile node moves, or when changing operation and management requirements call for mobility anchor switching, thus avoiding non-optimal routes. This draft proposes distributed mobility anchoring to enable making such route changes. Distributed mobility anchoring employs multiple anchors in the data plane. In general, the control plane function may be separate from - the data plane functions and be centralized but may also co-located - with the data plane function at these distributed anchors. Different - configurations (Section 3.1) of distributed anchoring are then - possible. Yet the distributed anchors need to have expected - behaviors (Section 3.2). + the data plane functions and be centralized but may also be co- + located with the data plane function at these distributed anchors. + Different configurations (Section 3.1) of distributed mobility + anchoring are then possible. The configurations of distributed + anchoring for network-based mobility support in a flat network, for + network-based mobility support in a hierarchical network, and for + host-based mobility support are described respectively in + Section 3.1.1, Section 3.1.2, and Section 3.1.3. Mobility functions + at the anchors and nodes are required to perform with expected + behaviors (Section 3.2). The LM behaviors and mobility message + parameters are described in Section 3.2.1, whereas the FM behaviors + and mobility message parameters are described in Section 3.2.2. - A mobile node (MN) attached to an access router of a network may be - allocated an IP prefix which is anchored to that router. It may then - use the IP address configured from this prefix as the source IP - address to run a flow with its correspondent node (CN). When there - are multiple anchors, the flow may need to select the anchor when it - is initiated (Section 4). Using an anchor in MN's network of - attachment has the advantage that the packets can simply be forwarded - according to the forwarding table. Although the anchor is in the - MN's network of attachment when the flow was initiated, the MN may - later move to another network, so that the IP address no longer - belongs to the new network of attachment of the MN. Whether the flow - needs session continuity will determine how to ensure that the IP - address of the flow will be anchored to the new network of - attachment. If the ongoing IP flow can cope with an IP prefix/ - address change, the flow can be reiniated with a new IP address - anchored in the new network (Section 4.1.1). On the other hand, if - the ongoing IP flow cannot cope with such change, the IP address - anchoring can be moved from the original network to the new network - (Section 4.2). + A mobile node (MN) attached to an access router of a network or + network slice may be allocated an IP prefix which is anchored to that + router. It may then use an IP address configured from this prefix as + the source IP address to run a flow with its correspondent node (CN). + When there are multiple anchors, an address selection for a given + flow is first required before the flow is initiated. Using an anchor + in MN's network of attachment has the advantage that the packets can + simply be forwarded according to the forwarding table. Although the + anchor is in the MN's network of attachment when the flow was + initiated, the MN may later move to another network, so that the IP + address no longer belongs to the current network of attachment of the + MN. + + Whether the flow needs session continuity will determine how to + ensure that the IP address of the flow will be anchored to the new + network of attachment. If the ongoing IP flow can cope with an IP + prefix/address change, the flow can be reinitiated with a new IP + address anchored in the new network (Section 4.1). On the other + hand, if the ongoing IP flow cannot cope with such change, mobility + support is needed (Section 4.2). A network or network slice + supporting a mix of flows requiring and not requiring IP mobility + support will need to distinguish these flows. The guidelines for + such network or network slice are described in Section 4.1.1. The + general guidelines for such network or network slice to provide IP + mobility support are described in Section 4.2.1. + + Specifically, IP mobility support can be provided by changing the + anchoring of the IP prefix/address of the flow from the home network + of the flow to the new network of attachment Section 5. The basic + case may be with network-based mobility for a flat network + configuration described in Section 5.1 with the guidelines described + in Section 5.1.1. This case is discussed further with a centralized + control plane in Section 5.2 with additional guidelines described in + Section 5.2.1. A level of hierarchy of nodes may then be added to + the network configuration. Mobility involving change in the DPN + without changing the DPA is described in Section 5.3 with additional + guidelines described in Section 5.3.1 Mobility involving change in + the DPN without changing the DPA is described in Section 5.4 with + additional guidelines described in Section 5.4.1 2. Conventions and Terminology - The key words "MUST", "MUST NOT", "REQUIRED", "SHALL","SHALL NOT", + The key words "MUST", "MUST NOT", "GLUIRED", "SHALL","SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. All general mobility-related terms and their acronyms used in this - document are to be interpreted as defined in the Mobile IPv6 base - specification [RFC6275], the Proxy Mobile IPv6 specification - [RFC5213], and the DMM current practices and gap analysis [RFC7429]. - This includes terms such as mobile node (MN), correspondent node + document are to be interpreted as defined in the Mobile IPv6 (MIPv6) + base specification [RFC6275], the Proxy Mobile IPv6 (PMIPv6) + specification [RFC5213], the "Mobility Related Terminologies" + [RFC3753], and the DMM current practices and gap analysis [RFC7429]. + + These include terms such as mobile node (MN), correspondent node (CN), home agent (HA), home address (HoA), care-of-address (CoA), local mobility anchor (LMA), and mobile access gateway (MAG). - In addition, this document uses the following term: + In addition, this document uses the following terms: Home network of an application session (or of an HoA): the network that has allocated the IP address (HoA) used for the session - identifier by the application running in an MN. An MN may be + identifier by the application running in an MN. The MN may be running multiple application sessions, and each of these sessions can have a different home network. IP prefix/address anchoring: An IP prefix, i.e., Home Network Prefix (HNP), or address, i.e., Home Address (HoA), allocated to a mobile - node is topologically anchored to a node when the anchor node is - able to advertise a connected route into the routing + node is topologically anchored to an anchor node when the anchor + node is able to advertise a connected route into the routing infrastructure for the allocated IP prefix. Internetwork Location Management (LM) function: managing and keeping track of the internetwork location of an MN. The location information may be a binding of the IP advertised address/prefix, e.g., HoA or HNP, to the IP routing address of the MN or of a node - that can forward packets destined to the MN. It is a control - plane function. + that can forward packets destined to the MN. + + When the MN is a mobile router (MR) carrying a mobile network of + mobile network nodes (MNN), the location information will also + include the IP prefixes delegated to the MR to be allocated to the + MNNs in the mobile network. + + LM is a control plane function. In a client-server protocol model, location query and update messages may be exchanged between a Location Management client (LMc) and a Location Management server (LMs). + Optionally, there may be a Location Management proxy (LMp) between + LMc and LMs. + With separation of control plane and data plane, the LM function is in the control plane. It may be a logical function at the control plane node, control plane anchor, or mobility controller. It may be distributed or centralized. Forwarding Management (FM) function: packet interception and forwarding to/from the IP address/prefix assigned to the MN, based on the internetwork location information, either to the destination or to some other network element that knows how to forward the packets to their destination. - This function may be used to achieve indirection. With separation - of control plane and data plane, FM may split into a FM function - in the data plane (FM-DP) and a FM function in the control plane - (FM-CP). + This function may be used to achieve traffic indirection. With + separation of control plane and data plane, the FM function may + split into a FM function in the data plane (FM-DP) and a FM + function in the control plane (FM-CP). FM-DP may be distributed with distributed mobility management. It may be a function in a data plane anchor or data plane node. FM-CP may be distributed or centralized. It may be a function in a control plane node, control plane anchor or mobility controller. Security Management (SM) function: The security management function controls security mechanisms/protocols providing access control, integrity, authentication, authorization, confidentiality, etc. for the control plane and data plane. This function resides in all nodes such as control plane anchor, data plane anchor, mobile node, and correspondent node. -3. Distributed anchoring +3. Distributed Mobility Anchoring -3.1. Distributed anchoring configurations +3.1. Distributed Anchoring Configurations for Different Networks or + Network Slices The mobility functions may be implemented in different configurations of distributed anchoring in architectures separating the control and data planes. The separation as described in - [I-D.wt-dmm-deployment-models] has defined home control plane anchor - (Home-CPA), home data plane anchor (Home-DPA), access control plane - node (Access-CPN), and access data plane node (Access-DPN), which are - respectively abbreviated as CPA, DPA, CPN, and DPN here. Some - configurations are described in [I-D.sijeon-dmm-deployment-models]. + [I-D.ietf-dmm-deployment-models] has defined home control plane + anchor (Home-CPA), home data plane anchor (Home-DPA), access control + plane node (Access-CPN), and access data plane node (Access-DPN), + which are respectively abbreviated as CPA, DPA, CPN, and DPN here. + Some configurations are described in + [I-D.sijeon-dmm-deployment-models]. - Figure 1 shows 4 configurations of network-based mobility management. - In each configuration, an MN is allocated an IP prefix/address IP1 - and is using IP1 to communicate with a correspondent node (CN) not - shown in the figure. The flow of this communication session is shown - as flow(IP1, ...) which uses IP1 and other parameters. + Different networks or different network slices may have different + configurations of distributed anchoring. - (a) (b) (c) (d) - +-----+ +-----+ - |LMs | |LMs | - +-----+ +-----+ + The configurations also differ depending on whether the desired + mobility support is network-based for a flat network (Section 3.1.1), + is network-based for a hierarchical network (Section 3.1.2), or is + host-based (Section 3.1.3). + +3.1.1. Distributed Anchoring with Network-based Mobility Support for + Flat Network + + Figure 1 shows 2 configurations of network-based mobility management + for a flat network. + + (a) (b) + +-----+ + |LMs | + +-----+ + +------------+ +------------+ + |CPA: | |CPA: | + |FM-CP, LM | |FM-CP, LMc | + +------------+ +------------+ +------------+ +------------+ +------------+ +------------+ - |CPA: | |CPA: | |CPA: | |CPA: | - |FM-CP, LM | |FM-CP, LMc | |FM-CP, LMs | |FM-CP, LMp | + |DPA(IPa1): | |DPA(IPa2): | |DPA(IPa1): | |DPA(IPa2): | + |anchors IP1 | |anchors IP2 | ... |anchors IP1 | |anchors IP2 | ... + |FM-DP | |FM-DP | |FM-DP | |FM-DP | +------------+ +------------+ +------------+ +------------+ + + +------------+ +------------+ + |MN(IP1) | |MN(IP1) | + |flow(IP1,..)| |flow(IP1,..)| + +------------+ +------------+ + + Figure 1. Configurations of network-based mobility management for a + flat network (a) FM-CP and LM at CPA, FM-DP at DPA; (b) Separate LMs, + FM-CP and LMc at CPA, FM-DP at DPA. + + Figure 1 also shows a distributed mobility anchoring environment with + multiple instances of the DPA. + + There is FM-DP function at each of the distributed DPA. + + The control plane may either be distributed (not shown) or + centralized. When the CPA co-locates with the distributed DPA there + will be multiple instances of the co-located CPA and DPA (not shown). + + There is FM-CP function at the CPA. + + MN is allocated an IP prefix/address IP1 which is anchored to the DPA + with the IP prefix/address IPa1. It is using IP1 to communicate with + a correspondent node (CN) not shown in the figure. The flow of this + communication session is shown as flow(IP1, ...) which uses IP1 and + other parameters. + + In Figure 1(a), LM and FM-CP co-locate at CPA. + + Then LM may be distributed or centralized according to whether the + CPA is distributed (not shown) or centralized. + + Figure 1(b) differs from Figure 1(a) in that the LM function is split + into a server LMs and a client LMc. + + LMc and FM-CP co-locate at the CPA. + + The LMs may be centralized whereas the LMc may be distributed or + centralized according to whether the CPA is distributed (not shown) + or centralized. + +3.1.2. Distributed Anchoring with Network-based Mobility Support for + Hierarchical Network + + Figure 2 shows 2 configurations of network-based mobility management + for a hierarchical network. + + (a) + +------------+ + |CPA: | + |FM-CP, LMs | + +------------+ + +------------+ +------------+ + |DPA(IPa1): | |DPA(IPa2): | + |anchors IP1 | |anchors IP2 | ... + |FM-DP | |FM-DP | + +------------+ +------------+ + + +------------+ + |CPN: | + |FM-CP, LMc | + +------------+ +------------+ +------------+ +------------+ +------------+ - |DPA(IPa1): | |DPA(IPa1): | |DPA(IPa1): | |DPA(IPa1): | - |anchors IP1 | |anchors IP1 | |anchors IP1 | |anchors IP1 | - |FM-DP | |FM-DP | |FM-DP | |FM-DP | + |DPN(IPn11): | |DPN(IPn12): | |DPN(IPn21): | |DPN(IPn22) | + |FM-DP | |FM-DP | ... |FM-DP | |FM-DP | ... +------------+ +------------+ +------------+ +------------+ +------------+ +------------+ - |CPN: | |CPN: | - |FM-CP, LMc | |FM-CP, LMc | + |MN(IP1) | |MN(IP2) | + |flow(IP1,..)| |flow(IP2,..)| +------------+ +------------+ + + Figure 2(a). Configurations of network-based mobility management for + a hierarchical network with FM-CP and LMs at CPA, FM-DP at DPA; FM-CP + and LMc at CPN, FM-DP at DPN. + + (b) + +-----+ + |LMs | + +-----+ + + +------------+ + |CPA: | + |FM-CP, LMp | + +------------+ +------------+ +------------+ - |DPN(IPn1): | |DPN(IPn1): | + |DPA(IPa1): | |DPA(IPa2): | + |anchors IP1 | |anchors IP2 | ... |FM-DP | |FM-DP | +------------+ +------------+ + +------------+ + |CPN: | + |FM-CP, LMc | + +------------+ +------------+ +------------+ +------------+ +------------+ - |MN(IP1) | |MN(IP1) | |MN(IP1) | |MN(IP1) | - |flow(IP1,..)| |flow(IP1,..)| |flow(IP1,..)| |flow(IP1,..)| + |DPN(IPn11): | |DPN(IPn12): | |DPN(IPn21): | |DPN(IPn22) | + |FM-DP | |FM-DP | ... |FM-DP | |FM-DP | ... +------------+ +------------+ +------------+ +------------+ - Figure 1. (a) FM-CP and LM at CPA, FM-DP at DPA; (b) Separate LMs, - FM-CP and LMc at CPA, FM-DP at DPA; (c) FM-CP and LMs at CPA, FM-DP - at DPA, FM-CP and LMc at CPN, FM-DP at DPN; (d) Separate LMs, FM-CP - and LMp at CPA, FM-DP at DPA, FM-CP and LMc at CPN, FM-DP at DPN. + +------------+ +------------+ + |MN(IP1) | |MN(IP2) | + |flow(IP1,..)| |flow(IP2,..)| + +------------+ +------------+ - In Figures 1(a), 1(b), 1(c), and 1(d), the IP address of the MN, IP1, - is anchored to the DPA which has the IP prefix/address IPa1. The - data plane is distributed so that there may be multiple instances of - the DPA (not shown). The control plane may either be distributed or - centralized. When the CPA co-locates with the distributed DPA there - will be multiple instances of the co-located CPA and DPA (not shown). + Figure 2(b). Configurations of network-based mobility management for + a hierarchical network with separate LMs, FM-CP and LMp at CPA, FM-DP + at DPA; FM-CP and LMc at CPN, FM-DP at DPN. - In Figure 1(a) and Figure 1(b), the network is flat with FM-DP at the - distributed DPA. + Figures 2 also shows a distributed mobility anchoring environment + with multiple instances of the DPA. - In Figure 1(a), LM and FM-CP co-locate at CPA. Then LM may be - distributed or centralized according to whether the CPA is - distributed or centralized. + In the hierarchy, there may be multiple DPN's for each DPA. - Figure 1(b) differs from Figure 1(a) in that the LM function is split - into a server LMs and a client LMc. LMc and FM-CP are at the CPA. - The LMs may be centralized whereas the LMc may be distributed or - centralized according to whether the CPA is distributed or + There is FM-DP at each of the distributed DPA and at each of the + distributed DPN. + + The control plane may either be distributed (not shown) or centralized. - In Figure 1(c) and Figure 1(d), the network is hierarchical where - there may be multiple DPN's for each DPA. There is FM-DP at each of - the distributed DPA and at each of the distributed DPN. + When the CPA co-locates with the distributed DPA there will be + multiple instances of the co-located CPA and DPA (not shown). - In Figure 1(c), LMs and FM-CP are at the CPA. In addition, there are - FM-CP and LMc at the CPN. Again, LMs may be distributed or + When the CPN co-locates with the distributed DPN there will be + multiple instances of the co-located CPN and DPN (not shown). + + There is FM-CP function at the CPA and at the CPN. + + MN is allocated an IP prefix/address IP1 which is anchored to the DPA + with the IP prefix/address IPa1. It is using IP1 to communicate with + a correspondent node (CN) not shown in the figure. The flow of this + communication session is shown as flow(IP1, ...) which uses IP1 and + other parameters. + + In Figure 2(a), LMs and FM-CP are at the CPA. In addition, there are + FM-CP and LMc at the CPN. + + LMs may be distributed or centralized according to whether the CPA is + distributed or centralized. The CPA may co-locate with DPA or may + separate. + + Figure 2(b) differs from Figure 2(a) in that the LMs is separated + out, and a proxy LMp is added between the LMs and LMc. + + LMp and FM-CP co-locate at the CPA. + + FM-CP and LMc co-locate at the CPN. + + The LMs may be centralized whereas the LMp may be distributed or centralized according to whether the CPA is distributed or - centralized. The CPA may co-locate with DPA or may separate. + centralized. - Figure 1(d) differs from Figure 1(c) in that the LMs is separated - out, and a proxy LMp is added between the LMs and LMc. LMp and FM-CP - are at the CPA. Again, there are FM-CP and LMc at the CPN. The LMs - may be centralized whereas the LMp may be distributed or centralized - according to whether the CPA is distributed or centralized. +3.1.3. Distributed Anchoring for Host-based Mobility Support Host-based variants of the mobility function configurations from - Figures 1(c) and 1(d) are shown in Figures 2(a) and 2(b) where the - role to perform mobility functions by CPN and DPN are now taken by - the MN. The MN then need to possess the mobility functions FM and - LMc. + Figures 2(a) and 2(b) are respectively shown in Figures 3(a) and 3(b) + where the role to perform mobility functions by CPN and DPN are now + taken by the MN. The MN then needs to possess the mobility functions + FM and LMc. (a) (b) +-----+ |LMs | +-----+ +------------+ +------------+ |CPA: | |CPA: | |FM-CP, LMs | |FM-CP, LMp | +------------+ +------------+ - +------------+ +------------+ - |DPA(IPa1): | |DPA(IPa1): | - |anchors IP1 | |anchors IP1 | - |FM-DP | |FM-DP | - +------------+ +------------+ + +------------+ +------------+ +------------+ +------------+ + |DPA(IPa1): | |DPA(IPa2): | |DPA(IPa1): | |DPA(IPa2): | + |anchors IP1 | |anchors IP2 | ... |anchors IP1 | |anchors IP2 | ... + |FM-DP | |FM-DP | |FM-DP | |FM-DP | + +------------+ +------------+ +------------+ +------------+ +------------+ +------------+ |MN(IP1) | |MN(IP1) | |flow(IP1,..)| |flow(IP1,..)| |FM, LMc | |FM, LMc | +------------+ +------------+ - Figure 2. (a) FM-CP and LMs at CPA, FM-DP at DPA, FM and LMc at MN; - (b) Separate LMs, FM-CP and LMp at CPA, FM-DP at DPA, FM and LMc at - MN. + Figure 3. Configurations of host-based mobility management (a) FM-CP + and LMs at CPA, FM-DP at DPA, FM and LMc at MN; (b) Separate LMs, FM- + CP and LMp at CPA, FM-DP at DPA, FM and LMc at MN. - In Figure 2(a) and Figure 2(b), FM-DP is at the distributed DPA as - before. + Figure 3 shows 2 configurations of host-based mobility management + with multiple instances of DPA for a distributed mobility anchoring + environment. - In Figure 2(a), LMs and FM-CP are at the CPA. The LMs may be - distributed or centralized according to whether the CPA is - distributed or centralized. + There is FM-DP function at each of the distributed DPA. - Figure 2(b) differs from Figure 2(a) in that the LMs is separated out - and the proxy LMp is added between the LMs and LMc. LMp and FM-CP - are at the CPA. The FMs may be centralized whereas the LMp may be - distributed or centralized according to whether the CPA is - distributed or centralized. + The control plane may either be distributed (not shown) or + centralized. -3.2. Distributed anchoring behaviors and message information elements + When the CPA co-locates with the distributed DPA there will be + multiple instances of the co-located CPA and DPA (not shown). + + There is FM-CP function at the CPA. + + The MN possesses the mobility functions FM and LMc. + + MN is allocated an IP prefix/address IP1 which is anchored to the DPA + with the IP prefix/address IPa1. It is using IP1 to communicate with + a correspondent node (CN) not shown in the figure. The flow of this + communication session is shown as flow(IP1, ...) which uses IP1 and + other parameters. + + In Figure 3(a), LMs and FM-CP co-locate at the CPA. + + The LMs may be distributed or centralized according to whether the + CPA is distributed (not shown) or centralized. + + Figure 3(b) differs from Figure 3(a) in that the LMs is separated out + and the proxy LMp is added between the LMs and LMc. + + LMp and FM-CP co-locate at the CPA. + + The LMs may be centralized whereas the LMp may be distributed or + centralized according to whether the CPA is distributed (not shown) + or centralized. + +3.2. Distributed Anchoring Behaviors and Mobility Message Parameters The behaviors of distributed anchoring are defined in this section in order that they may work together in expected manners to produce a - distributed mobility solution. The needed information elements are - passed as message parameters. + distributed mobility solution. The needed information are passed as + mobility message parameters. -3.2.1. Location management behaviors and message information elements + The mobility needs in 5G Wireless and beyond are diverse. Therefore + the behaviors needed to enable different distributed mobility + solutions in different distributed anchoring configurations are + extensive and are listed below. It is however not necessary for + every distributed mobility solution to exhibit all the behaviors + listed in this section. A given distributed mobility solution may + exhibit the behaviors as needed. - It is seen in (Section 3.1) that +3.2.1. Location Management Behaviors and Mobility Message Parameters - (1) LMs may be a separate server or may co-locate with LMc at CPA; - (2) LMc may be at CPA, CPN, or MN. + An example LM design consists of a distributed database with multiple + LMs servers. The location information about the prefix/address of an + MN is primarily at a given LMs. Peer LMs may exchange the location + information with each other. LMc may retrieve a given record or send + a given record update to LMs. - Example LM design may consists of a distributed database of LMs - servers in a pool of distributed servers. The location information - about the prefix/address of a MN is primarily at a given LMs. Peer - LMs may exchange the location information with each other. LMc may - retrieve a given record or send a given record update to LMs. + Location management behaviors: - Location information bebaviors: + LM-cfg: As shown in Section 3.1: - (LM:1) LM may manage the location information in a client-server - database system. The example LM database functions are: + LMs may be implemented at CPA, may co-locate with LMc at CPA, + or may be a separate server. - (LM:1-1) LMc may query LMs about location information for a - prefix of MN (pull). + LMc may be at CPA, CPN, or MN. + + LMp may proxy between LMs and LMc. + + Specifically: + + LM-cfg:1 LMs may co-locate with LMc at CPA in a flat network with + network-based mobility as shown in Figure 1(a) in + Section 3.1.1. + + LM-cfg:2 LMs may be a separate server whereas LMc is implemented in + CPA in a flat network with network-based mobility as shown + in Figure 1(b) in Section 3.1.1. + + LM-cfg:3 LMs may be implemented at CPA, whereas LMc is implemented + at CPN in a hierarchical network with network-based + mobility as shown in Figure 2(a) in Section 3.1.2 or at MN + for host-based mobility as shown in Figure 3(a) in + Section 3.1.3. + + LM-cfg:4 LMs may be a separate server with LMp implemented at CPA + whereas LMc is implemented at CPN in a hierarchical network + with network-based mobility as shown in Figure 2(b) in + Section 3.1.2 or at MN for host-based mobility as shown in + Figure 3(b) in Section 3.1.3. + + LM-db: LM may manage the location information in a client-server + database system. + + Example LM database functions are as follows: + + LM-db:1 LMc may query LMs about location information for a prefix of + MN (pull). Parameters: IP prefix of MN. - (LM:1-2) LMs may reply to LMc query about location - information for a prefix of MN (pull). + LM-db:2 LMs may reply to LMc query about location information for a + prefix of MN (pull). Parameters: IP prefix of MN, - IP address of FM-DP/DPA/DPN to forward the packets - of the flow. + IP address of FM-DP/DPA/DPN to forward the packets of the + flow. - (LM:1-3) LMs may inform LMc about location information for a - prefix of MN (push). + LM-db:3 LMs may inform LMc about location information for a prefix + of MN (push). Parameters: IP prefix of MN, - IP address of FM-DP/DPA/DPN to forward the packets - of the flow. + IP address of FM-DP/DPA/DPN to forward the packets of the + flow. - (LM:1-4) LMc may inform LMs about update location - information for a prefix of MN. + This function in PMIPv6 protocol is the Update Notification + (UPN) together with the Update Notification Acknowledgment + (UPA) as defined in [RFC7077]. + + LM-db:4 LMc may inform LMs about update location information for a + prefix of MN. Parameters: IP prefix of MN, - IP address of FM-DP/DPA/DPN to forward the packets - of the flow. + IP address of FM-DP/DPA/DPN to forward the packets of the + flow. - (LM:2) The LM may be a distributed database with multiple LMs - servers. For example: + This function in MIPv6 / PMIPv6 protocol is the Binding + Update (BU) / Proxy Binding Update (PBU) together with the + Binding Acknowledgment (BA) / Proxy Binding Acknowledgment + (PBA) as defined in [RFC6275] / [RFC5213] respectively. - (LM:2-1) A LMs may join a pool of LMs servers. + LM-db:5 The MN may be a host or a router. When the MN is a mobile + router (MR), the prefix information above may include the + prefixes delegated to the MR. + Additional parameters: + IP prefix or prefixes delegated to the MR. + + LM-svr: The LM may be a distributed database with multiple LMs + servers. + + For example: + LM-svr:1 A LMs may join a pool of LMs servers. Parameters: IP address of the LMs, IP prefixes for which the LMs will host the primary location information. - (LM:2-2) LMs may query a peer LMs about location information - for a prefix of MN. + LM-svr:2 LMs may query a peer LMs about location information for a + prefix of MN. Parameters: IP prefix. - (LM:2-3) LMs may reply to a peer LMs about location - information for a prefix of MN. + LM-svr:3 LMs may reply to a peer LMs about location information for + a prefix of MN. Parameters: IP prefix of MN, - IP address of FM-DP/DPA/DPN to forward the packets - of the flow. + IP address of FM-DP/DPA/DPN to forward the packets of the + flow. -3.2.2. Forwarding management behaviors and message information elements + The parameters indicated above are only the minimal. In a specific + mobility protocol, additional parameters should be added as needed. - It is seen in (Section 3.1) that + Examples of these additional parameters are those passed in the + mobility options of the mobility header for MIPv6 [RFC6275] and for + PMIPv6 [RFC5213]. - (1) FM-CP may be at CPA, CPN, MN; - (2) FM-DP may be at DPA, DPN, MN. +3.2.2. Forwarding Management Behaviors and Mobility Message Parameters - The FM behaviors and message information elements are: + The FM behaviors and mobility message parameters are: - (FM:1) With distributed FM functions, the role of FM for a flow may - pass to another FM as the DPA or DPN changes. + FM-cfg: As shown in Section 3.1: - (FM:2) In addition to above, a flow/session may be stateful for the - required information for QoS, charging, etc. are needed. - These states need to be transferred from the old anchor to - the new anchor. + FM-CP may be implemented at CPA, CPN, MN depending on the + configuration chosen. - (FM:3) An anchor may act on packets on a per flow basis and perform - the changes to the forwarding path upon a change of point of - attachment of a MN: + FM-DP may also be implemented at CPA, CPN, MN depending on + the configuration chosen. - (FM:3-1) FM filters the packets up to the granularity of a - flow. - Example matching parameters are the 5-tuple of a - flow. + Specifically: - (FM:3-2) FM makes the necessary changes to the forwarding - path of a flow. - Example mechanism is through forwarding table - update activated by DHCPv6-PD. + FM-cfg:1 FM-CP and FM-DP may be implemented at CPA and DPA + respectively in a flat network with network-based mobility + as shown in Figure 1(a) and Figure 1(b) in Section 3.1.1. - (FM:3-3) FM reverts the previously made changes to the - forwarding path of a flow when such changes are no - longer needed, e.g., when ongoing flows using an IP - prefix/address requiring session continuity have - closed. - Example mechanism is through expiration of - DHCPv6-PD. + FM-cfg:2 FM-CP may be implemented at both CPA and CPN and FM-DP is + implemented at both DPA and DPN in a hierarchical network + with network-based mobility as shown in Figure 2(a) and + Figure 2(b) in Section 3.1.2. - (FM:4) An anchor may discover and be discovered such as through an - anchor registration system: + FM-cfg:3 FM-CP and FM-DP may be implemented at CPA and DPA + respectively and also both implemented at MN for host-based + mobility as shown in Figure 3(a) and Figure 3(b) in + Section 3.1.3. - (FM:4-1) FM registers and authenticates itself with a - centralized mobility controller. + FM-find:1 An anchor may discover and be discovered such as through + an anchor registration system as follows: + + FM-find:2 FM registers and authenticates itself with a centralized + mobility controller. Parameters: IP address of DPA and its CPA; IP prefix anchored to the DPA. - (FM:4-2) registration reply: acknowledge of registration and - echo the input parameters. + registration reply: acknowledge of registration and echo + the input parameters. - (FM:4-3) FM discovers the FM of another IP prefix by - querying the mobility controller based on the IP - prefix. + FM-find:3 FM discovers the FM of another IP prefix by querying the + mobility controller based on the IP prefix. Parameters: + IP prefix of MN. - (FM:4-4) when making anchor discovery FM expects the answer - parameters as: IP address of DPA to which IP prefix - of MN is anchored; IP prefix of the corresponding - CPA. + FM-find:4 when making anchor discovery FM expects the answer + parameters as: IP address of DPA to which IP prefix of MN + is anchored; IP prefix of the corresponding CPA. - (FM:5) With separation of control plane function and data plane - function, these function must work together. + FM-flow:1 The FM may be carried out on the packets to/from an MN up + to the granularity of a flow. - (FM:5-1) CPA/FM-CP sends forwarding table updates to DPA/FM- - DP. + FM-flow:2 Example matching parameters are in the 5-tuple of a flow. + + FM-cpdp:1 With separation of control plane function and data plane + function, FM-CP and FM-DP communicate with each other. + Such communication may be realized by the appropriate + messages in [I-D.ietf-dmm-fpc-cpdp]. For example: + + FM-cpdp:2 CPA/FM-CP sends forwarding table updates to DPA/FM-DP. Parameters: new forwarding table entries to add; expired forwarding table entries to delete. - (FM:5-2) DPA/FM-DP sends to CPA/FM-CP about its status and - load. + FM-cpdp:3 DPA/FM-DP sends to CPA/FM-CP about its status and load. Parameters: state of forwarding function being active or not; loading percentage. - (FM:6) An anchor can buffer packets of a flow in a mobility event: + FM-path:1 FM may change the forwarding path of a flow upon a change + of point of attachment of a MN. Prior to the changes, + packets coming from the CN to the MN would traverse from + the CN to the home network anchor of the flow for the MN + before reaching the MN. Changes are from this original + forwarding path or paths to a new forwarding path or paths + from the CN to the current AR of the MN and then the MN + itself. - (FM:6-1) CPA/FM-CP informs DPA/FM-DP to buffer packets of a - flow. + FM-path:2 As an incoming packet is forwarded from the CN to the MN, + the far end where forwarding path change begins may in + general be any node in the original forwarding path from + the CN to the home network DPA. The packet is forwarded + to the MN for host-based mobility and to a node in the + network which will deliver the packets to the MN for + network-based mobility. The near-end is generally a DPN + with a hierarchical network but may also be another node + with DPA capability in a flattened network. + + FM-path:3 The mechanisms to accomplish such changes may include + changes to the forwarding table and indirection such as + tunneling, rewriting packet header, or NAT. + + Note: An emphasis in this document in distributed mobility + anchoring is to explain the use of multiple anchors to + avoid unnecessarily long route which may be encountered in + centralized mobility anchoring. It is therefore not the + emphasis of this document on which particular mechanism to + choose from. + + FM-path-tbl:4 With forwarding table updates, changes to the + forwarding table are needed at each of the affected + forwarding switches in order to change the forwarding + path of the packets for the flow from that originally + between the CN and the home network anchor to that + between the CN and the new AR. + + Forwarding table updates may be achieved through BGP + update, but such updates may only be practical when + its scope is confined. An alternative is through + messaging between a centralized control plane and the + distributed forwarding switches. + + Forwarding table updates may be triggered using + DHCPv6-PD prefix delegation to change the role of IP + anchoring from the home network anchor (with FM-DP) to + the new anchor (with FM-DP) to which the MN is + currently attached. The new anchor will then + advertise routes for the delegated prefix. + + With a distributed routing protocol, the updates + spread out from neighbors to neighbors and will affect + all the forwarding switches such that the packets sent + from "any" node to MN will go to the new AR. + + Yet the scope of such updates for a given flow may be + confined to only those forwarding switches such that + the packets sent only from the "CN" to MN will go to + the new AR. Such confinement may be made when using a + centralized central plane possessing a global view of + all the forwarding switches. + + FM-path-tbl:5 FM reverts the changes previously made to the + forwarding path of a flow when such changes are no + longer needed, e.g., when all the ongoing flows using + an IP prefix/address requiring session continuity have + closed. When using DHCPv6-PD, the forwarding paths + will be reverted upon expiration of DHCPv6-PD. + + FM-path-ind:6 Indirection forwards the incoming packets of the flow + from the DPA at the far end to a DPA/DPN at the near + end of indirection. Both ends of the indirection + needs to know the LM information of the MN for the + flow and also needs to possess FM capability to + perform indirection. + + FM-path-ind:7 The mechanism of changing the forwarding path in + [RFC6275] and [RFC5213] is tunneling. In the control + plane, the FM-CP sets up the tunnel by instructing the + FM-DP at both ends of the tunnel. In the data plane, + the FM-DP at the start of the tunnel performs packet + encapsulation, whereas the FM-DP at the end of the + tunnel decapsulates the packet. + + Note that in principle the ends of the indirection + path can be any pair of network elements with the FM- + DP function. + + FM-path-ind:8 FM reverts the changes previously made to the + forwarding path of a flow when such changes are no + longer needed, e.g., when all the ongoing flows using + an IP prefix/address requiring session continuity have + closed. When tunneling is used, the tunnels will be + torn down when they are no longer needed. + + FM-DPA:1 Recall from above that for the incoming packets from the + CN, forwarding path change by FM is from the DPA at the far + end which may be at any forwarding switch (or even CN + itself) in the original forwarding path to the near end + DPA/DPN. + + It is necessary that any incoming packet from the CN of the + flow must traverse the DPA (or at least one of the DPAs, + e.g., in the case of anycast) at the far end in order for + the packet to detour to a new forwarding path. + + Therefore a convenient design is to locate the far end DPA + at a unique location which is always in the forwarding + path. This is the case in a centralized mobility design + where the DPA at the far end is the home network anchor of + the flow. + + Distributed mobility however may place the far end DPA at + other locations in order to avoid unnecessarily long route. + + FM-DPA:2 With multiple nodes possessing DPA capabilities, the role + of FM to begin path change for the incoming packets of a + flow at the home network DPA at the far end may be passed + to or added to that of another DPA. + + In particular, this DPA role may be moved upstream from the + home network DPA in the original forwarding path from CN to + MN. + + FM-DPA:3 Optimization of the new forwarding path may be achieved + when the path change for the incoming packets begins at a + DPA where the original path and the direct IPv6 path + overlaps. Then the new forwarding path will resemble the + direct IPv6 path from the CN to the MN. + + FM-DPA-tbl:4 Forwarding table updates, such as that triggered using + DHCPv6-PD prefix delegation to change the role of IP + anchoring from the home network anchor (DPA with FM-DP) + to the new anchor (DPA with FM-DP), may put the near + end of the path change at the new DPA. Subsequent + forwarding table updates may propagates upstream up to + a far end where the original path and the direct IPv6 + path overlaps. + + When that far end is too far upstream the signaling of + forwarding table updates may become excessive. An + alternative is to use indirection (see FM-DPA-ind) from + that far end to the new DPA at the near end. + + Still another alternative is to combine forwarding + table update with indirection. + + FM-DPA-tbl:5 Changes made by FM to the following tables, which are + IPv6 nodes, at the ends of the path change for a flow + will be reverted when the mobility support for the flow + is no longer needed, e.g., when the flows have + terminated. + + FM-DPA-ind:6 With indirection, locating or moving the FM function to + begin indirection upstream along the forwarding path + from CN to MN again may help to reduce unnecessarily + long path. + + FM-DPA-ind:7 Changes made by FM to establish indirection at the DPA + and DPN, which are IPv6 nodes, at the ends of the path + change for a flow will be reverted when the mobility + support for the flow is no longer needed, e.g., when + the flows have terminated. + + FM-state:1 In addition to the above, a flow/session may contain + states with the required information for QoS, charging, + etc. as needed. These states need to be transferred from + the old anchor to the new anchor. + + FM-buffer:1 An anchor can buffer packets of a flow in a mobility + event: + FM-buffer:2 CPA/FM-CP informs DPA/FM-DP to buffer packets of a flow. Trigger: MN leaves DPA in a mobility event. Parameters: IP prefix of the flow for which packets need to be buffered. - (FM:6-2) CPA/FM-CP on behalf of a new DPA/FM-DP informs the - CPA/FM-CP of the prior DPA/FM-DP that it is ready - to receive any buffered packets of a flow. + FM-buffer:3 CPA/FM-CP on behalf of a new DPA/FM-DP informs the CPA/ + FM-CP of the prior DPA/FM-DP that it is ready to receive + any buffered packets of a flow. Parameters: destination IP prefix of the flow's packets; IP address of the new DPA. -4. Example mobility solutions with distributed anchoring + FM-nemo:1 When the MN is a mobile router the access router anchoring + the IP prefix of MR will also anchor the IP prefix or + prefixes delegated to the MR. + +4. IP Mobility Handling in Distributed Anchoring Environments - + Mobility Support Only When Needed + + IP Mobility Support Only When Needed: + + IP mobility support may be provided only when needed instead of being + provided by default. The LM and FM functions in the different + configurations shown in Section 3.1 are then utilized only when + needed. + + A straightforward choice of mobility anchoring is for a flow to use + the IP prefix of the network to which the MN is attached when the + flow is initiated [I-D.seite-dmm-dma]. The IP prefix/address at the MN's side of a flow may be anchored at the access router to which the MN is attached. For example, when an MN attaches to a network (Net1) or moves to a new network (Net2), it - is allocated an IP prefix from that network. It configures from this + is allocated an IP prefix from the attached network. In addition to + configuring new link-local addresses, the MN configures from this prefix an IP address which is typically a dynamic IP address. It then uses this IP address when a flow is initiated. Packets to the MN in this flow are simply forwarded according to the forwarding table. - There may be multiple IP prefixes/addresses to choose from. They may - be from the same access network or different access networks. The - network may advertise these prefixes with cost options - [I-D.mccann-dmm-prefixcost] so that the mobile node may choose the - one with the least cost. In addition, these IP prefixes/addresses - may be of different types regarding whether mobility support is - needed [I-D.ietf-dmm-ondemand-mobility]. A flow will need to choose - the appropriate one according to whether it needs IP mobility - support. - -4.1. IP mobility support only when needed - - IP mobility support may be provided only when needed instead of being - provided by default. The simplest configuration in this case is - shown in Figures 1(a) and 1(b) in Section 3.1 for which the LM and FM - functions are utilized only when needed. - - A straightforward choice of mobility anchoring is for a flow to use - the IP prefix of the network to which the MN is attached when the - flow is initiated [I-D.seite-dmm-dma]. + There may be multiple IP prefixes/addresses that an MN can select + when initiating a flow. They may be from the same access network or + different access networks. The network may advertise these prefixes + with cost options [I-D.mccann-dmm-prefixcost] so that the mobile node + may choose the one with the least cost. In addition, these IP + prefixes/addresses may be of different types regarding whether + mobility support is needed [I-D.ietf-dmm-ondemand-mobility]. A flow + will need to choose the appropriate one according to whether it needs + IP mobility support. -4.1.1. Not needed: Changing to the new IP prefix/address +4.1. No Need of IP Mobility: Changing to New IP Prefix/Address When IP mobility support is not needed for a flow, the LM and FM - functions are not utilized so that the configuration from Figures - 1(a) and 1(b) in Section 3.1 simplifies to that shown in Figure 3. + functions are not utilized so that the configurations in Section 3.1 + are simplified as shown in Figure 4. Net1 Net2 +---------------+ +---------------+ |AR1 | |AR2 | +---------------+ +---------------+ |CPA: | |CPA: | |---------------| |---------------| |DPA(IPa1): | |DPA(IPa2): | |anchors IP1 | |anchors IP2 | +---------------+ +---------------+ +...............+ +---------------+ .MN(IP1) . move |MN(IP2) | .flow(IP1,...) . =======> |flow(IP2,...) | +...............+ +---------------+ - Figure 3. Changing to the new IP prefix/address. MN running a flow - using IP1 in Net1 changes to running a flow using IP2 in Net2. + Figure 4. Changing to the new IP prefix/address. MN running a flow + using IP1 in a network Net1 changes to running a flow using IP2 in + Net2. When there is no need to provide IP mobility to a flow, the flow may use a new IP address acquired from a new network as the MN moves to the new network. Regardless of whether IP mobility is needed, if the flow has terminated before the MN moves to a new network, the flow may subsequently restart using the new IP address allocated from the new network. When session continuity is needed, even if a flow is ongoing as the MN moves, it may still be desirable for the flow to change to using the new IP prefix configured in the new network. The flow may then close and then restart using a new IP address configured in the new network. Such a change in the IP address of the flow may be enabled using a higher layer mobility support which is not in the scope of this document. - In Figure 3, a flow initiated while the MN was in Net1 has terminated - before the MN moves to a new network Net2. After moving to Net2, the - MN uses the new IP prefix anchored in Net2 to start a new flow. The - packets may then be forwarded without requiring IP layer mobility - support. + In Figure 4, a flow initiated while the MN was in a network Net1 has + terminated before the MN moves to a new network Net2. After moving + to Net2, the MN uses the new IP prefix anchored in Net2 to start a + new flow. The packets may then be forwarded without requiring IP + layer mobility support. - The call flow is outlined in Figure 4. + An example call flow is outlined in Figure 5. MN p-AR n-AR CN |MN attaches to p-AR: | | | |acquire MN-ID and profile | | |--RS---------------->| | | | | | | |<----------RA(HNP1)--| | | | | | | Allocated prefix HNP1 IP1 address configuration @@ -595,45 +1019,106 @@ |--RS------------------------------>| | | | | | |<--------------RA(HNP2)------------| | | | | | Allocated prefix HNP2 IP2 address configuration | | | | |<-new Flow(IP2,IPcn,...)-----------+------------------------------->| | | | | - Figure 4. A flow uses the IP allocated from the network at which the - MN is attached when the flow is initiated. + Figure 5. Re-starting a flow to use the IP allocated from the + network at which the MN is attached. The security management function in the anchor node at a new network must allow to assign a valid IP prefix/address to a mobile node. -4.1.2. Needed: Providing IP mobility support +4.1.1. Guidelines for IPv6 Nodes: Changing to New IP Prefix/Address + + A network or network slice may not need IP mobility support. For + example, a network slice for stationary sensors only will never + encounter mobility. + + The standard functions in IPv6 already include dropping the old IPv6 + prefix/address and acquiring new IPv6 prefix/address when the node + changes its point of attachment to a new network. Therefore, a + network or network slice not providing IP mobility support at all + will not need any of the functions with the mobility behaviors and + messages described in Section 3.2. + + The guidelines for the IPv6 nodes in a network or network slice + supporting a mix of flows requiring and not requiring IP mobility + support include the following: + + GL-cfg:1 A network or network slice supporting a mix of flows + requiring and not requiring mobility support may take any + of the configurations described in Section 3.1 and need to + implement in the appropriate IPv6 nodes the mobility + functions LM and FM as described respectively in LM-cfg and + FM-cfg in Section 3.2 according to the configuration + chosen. + + GL-mix:1 These mobility functions possess some of the behaviors and + messages described in Section 3.2 depending on which + mobility mechanisms are used. Yet these mobility functions + must not be invoked for a flow that does not need IP + mobility support. It is necessary to be able to + distinguish the needs of a flow. The guidelines for the MN + and the AR are in the following. + + GL-mix:2 Regardless of whether there are flows requiring IP mobility + support, when the MN changes its point of attachment to a + new network, it needs to configure a new global IP address + for use in the new network in addition to configuring the + new link-local addresses. + + GL-mix:3 The MN needs to check whether a flow needs IP mobility + support. This can be performed when the application was + initiated. The specific method is not in the scope of this + document. + + GL-mix:4 The information of whether a flow needs IP mobility support + is conveyed to the network such as by choosing an IP + address to be provided with mobility support as described + in [I-D.ietf-dmm-ondemand-mobility]. Then as the MN + attaches to a new network, if the MN was using an IP + address that is not supposed to be provided with mobility + support, the access router will not invoke the mobility + functions described in Section 3.2 for this IP address. + That is, the IP address from the prior network is simply + not used in the new network. + + The above guidelines are only to enable distinguishing whether there + is need of IP mobility support for a flow that does not. When the + flow needs IP mobility support, the list of guidelines will continue + in Section 4.2.1. + +4.2. Need of IP Mobility When IP mobility is needed for a flow, the LM and FM functions in - Figures 1(a) and 1(b) in Section 3.1 are utilized. The mobility - support may be provided by IP prefix anchor switching to the new - network to be described in Section 4.2 or by using other mobility - management methods ([Paper-Distributed.Mobility.PMIP] and + Section 3.1 are utilized. The mobility support may be provided by IP + prefix anchor switching to the new network to be described in + Section 5 or by using other mobility management methods + ([Paper-Distributed.Mobility.PMIP] and [Paper-Distributed.Mobility.Review]). Then the flow may continue to - use the IP prefix from the prior network. Yet some time later, the - user application for the flow may be closed. If the application is - started again, the new flow may not need to use the prior network's - IP address to avoid having to invoke IP mobility support. This may - be the case where a permanent IP prefix/address is not used. The - flow may then use the new IP prefix in the network where the flow is - being initiated. Routing is again kept simpler without employing IP - mobility and will remain so as long as the MN has not moved away from - that network. + use the IP prefix from the prior network of attachment. Yet some + time later, the user application for the flow may be closed. If the + application is started again, the new flow may not need to use the + prior network's IP address to avoid having to invoke IP mobility + support. This may be the case where a dynamic IP prefix/address + rather than a permanent one is used. The flow may then use the new + IP prefix in the network where the flow is being initiated. Routing + is again kept simpler without employing IP mobility and will remain + so as long as the MN which is now in the new network has not moved + again and left to another new network. - The call flow in this case is outlined in Figure 5. + An example call flow in this case is outlined in Figure 6. MN p-AR n-AR CN |MN attaches to p-AR: | | | |acquire MN-ID and profile | | |--RS---------------->| | | | | | | |<----------RA(HNP1)--| | | | | | | Allocated prefix HNP1 IP1 address configuration @@ -646,69 +1131,114 @@ |--RS------------------------------>| | IP mobility support such as that described in next sub-section |<--------------RA(HNP2,HNP1)-------| | | | | | |<-Flow(IP1,IPcn,...)---------------+------------------------------->| | | | | Allocated prefix HNP2 IP2 address configuration | | | | -Flow(IP1,IPcn) teminates +Flow(IP1,IPcn) terminates | | | | |<-new Flow(IP2,IPcn,...)-----------+------------------------------->| | | | | - Figure 5. A flow uses the IP allocated from the network at which the - MN is attached when the flow is initiated. + Figure 6. A flow continues to use the IP from its home network after + MN has moved to a new network. - To provide IP mobility support with distributed anchoring, the - distributed anchors may need to message with each other. When such - messaging is needed, the anchors may need to discover each other as - described in the FM behaviors and information elements (FM:4) in - Section 3.2.2. +4.2.1. Guidelines for IPv6 Nodes: Need of IP Mobility - Then the anchors need to properly forward the packets of the flows as - described in the FM behaviors and information elements (FM:3) in - Section 3.2.2. + The configuration guidelines of distributed mobility for the IPv6 + nodes in a network or network slice supporting a mix of flows + requiring and not requiring distributed mobility support are as + follows: - If there are in-flight packets toward the old anchor while the MN is - moving to the new anchor, it may be necessary to buffer these packets - and then forward to the new anchor after the old anchor knows that - the new anchor is ready. Such are described in the FM behaviors and - information elements (FM:6) in Section 3.2.2. + GL-cfg:2 Multiple instances of DPAs (at access routers) which are + providing IP prefix to the MNs are needed to provide + distributed anchoring in an appropriate configuration such + as those in Figure 1 (Section 3.1.1) for network-based + distributed mobility or in Figure 3 (Section 3.1.3) for + host-based distributed mobility. -4.2. IP prefix/address anchor switching to the new network + The appropriate IPv6 nodes (CPA, DPA, CPN, DPN) are to be + implemented the mobility functions LM and FM as described + respectively in LM-cfg and FM-cfg in Section 3.2 according + to the configuration chosen. + + The guidelines of distributed mobility for the IPv6 nodes in a + network or network slice supporting a mix of flows requiring and not + requiring distributed mobility support had begun with those given as + GL-mix in Section 4.1.1 and continue as follows: + + GL-mix:5 The distributed anchors may need to message with each + other. When such messaging is needed, the anchors may need + to discover each other as described in the FM behaviors and + mobility message parameters (FM-find) in Section 3.2.2. + + GL-mix:6 The anchors may need to provide mobility support on a per- + flow basis as described in the FM behaviors and mobility + message parameters (FM-flow) in Section 3.2.2. + + GL-mix:7 Then the anchors need to properly forward the packets of + the flows as described in the FM behaviors and mobility + message parameters (FM-path, FM-path-tbl, FM-DPA, FM-DPA- + tbl) in Section 3.2.2. + + GL-mix:8 If there are in-flight packets toward the old anchor while + the MN is moving to the new anchor, it may be necessary to + buffer these packets and then forward to the new anchor + after the old anchor knows that the new anchor is ready. + Such are described in the FM behaviors and mobility message + parameters (FM-buffer) in Section 3.2.2. + +5. IP Mobility Handling in Distributed Anchoring Environments - Anchor + Switching to the New Network + + IP Prefix/Address Anchor Switching to the New Network: + + IP mobility is invoked to enable session continuity for an ongoing + flow as the MN moves to a new network. Here the anchoring of the IP + address of the flow is in the home network of the flow, which is not + in the current network of attachment. A centralized mobility + management mechanism may employ indirection from the anchor in the + home network to the current network of attachment. Yet it may be + difficult to avoid unnecessarily long route when the route between + the MN and the CN via the anchor in the home network is too much + longer than the direct route between them. An alternative is to + switch the IP prefix/address anchoring to the new network. + +5.1. IP Prefix/Address Anchor Switching for Flat Network The IP prefix/address anchoring may move without changing the IP prefix/address of the flow. Here the LM and FM functions in Figures - 1(a) and 1(b) in Section 3.1 are implemented as shown in Figure 6. + 1(a) and 1(b) in Section 3.1 are implemented as shown in Figure 7. Net1 Net2 +---------------+ +---------------+ |AR1 | |AR2 | +---------------+ +---------------+ |CPA: | |CPA: | |LM:IP1<-->IPa2 | |LM:IP1<-->IPa2 | |---------------| |---------------| |DPA(IPa1): | |DPA(IPa2): | |anchors IP1 | move |anchors IP2,IP1| |FM:DHCPv6-PD | =======> |FM:DHCPv6-PD | +---------------+ +---------------+ +...............+ +---------------+ .MN(IP1) . move |MN(IP2,IP1) | .flow(IP1,...) . =======> |flow(IP1,...) | +...............+ +---------------+ - Figure 6. IP prefix/address anchor switching to the new network. MN + Figure 7. IP prefix/address anchor switching to the new network. MN with flow using IP1 in Net1 continues to run the flow using IP1 as it moves to Net2. As an MN with an ongoing session moves to a new network, the flow may preserve session continuity by moving the anchoring of the original IP prefix/address of the flow to the new network. An example is in the use of BGP UPDATE messages to change the forwarding table entries as described in [I-D.mccann-dmm-flatarch] and also for 3GPP Evolved Packet Core (EPC) network in [I-D.matsushima-stateless-uplane-vepc]. However, the response time and scalability of using a distributed @@ -706,80 +1236,107 @@ moves to Net2. As an MN with an ongoing session moves to a new network, the flow may preserve session continuity by moving the anchoring of the original IP prefix/address of the flow to the new network. An example is in the use of BGP UPDATE messages to change the forwarding table entries as described in [I-D.mccann-dmm-flatarch] and also for 3GPP Evolved Packet Core (EPC) network in [I-D.matsushima-stateless-uplane-vepc]. However, the response time and scalability of using a distributed routing protocol to update forwarding tables may be controversial. - Use of a centralized routing protocol with a centralized control - plane as described in Section 4.2.1 will be more scalable. + plane as described in Section 5.2 will be more scalable. - The location management provides information about which IP prefix - from an AR in the original network is being used by a flow in which - AR in a new network. Such information needs to be deleted or updated - when such flows have closed so that the IP prefix is no longer used - in a different network. The LM behaviors are described in - Section 3.2.1. +5.1.1. Guidelines for IPv6 Nodes: Switching Anchor for Flat Network - The FM functions are implemented through the DHCPv6-PD protocol. - Here the anchor behavior to properly forward the packets for a flow - as described in the FM behaviors and information elements FM:3 in - Section 3.2.2 is realized by changing the anchor with DHCPv6-PD and - also by reverting such changes later after the application has - already closed and when the DHCPv6-PD timer expires. If there are - in-flight packets toward the old anchor while the MN is moving to the - new anchor, it may be necessary to buffer these packets and then - forward to the new anchor after the old anchor knows that the new - anchor is ready. Such are described in the FM behaviors and - information elements FM:6 in Section 3.2.2. The anchors may also - need to discover each other as described in the FM behaviors and - information elements FM:4. + The configuration guideline for a flat network or network slice + supporting a mix of flows requiring and not requiring IP mobility + support is: - The security management function in the anchor node at a new network - must allow to assign the original IP prefix/address used by the - mobile node at the previous (original) network. As the assigned - original IP prefix/address is to be used in the new network, the - security management function in the anchor node must allow to - advertise the prefix of the original IP address and also allow the - mobile node to send and receive data packets with the original IP - address. + GL-cfg:3 Multiple instances of DPAs (at access routers) which are + providing IP prefix to the MNs are needed to provide + distributed anchoring according to Figure 1(a) or + Figure 1(b)in Section 3.1 for a flat network. - The security management function in the mobile node must allow to - configure the original IP prefix/address used at the previous - (original) network when the original IP prefix/address is assigned by - the anchor node in the new network. The security management function - in the mobile node also allows to use the original IP address for the + The appropriate IPv6 nodes (CPA, DPA) are to be implemented + the mobility functions LM and FM as described respectively + in LM-cfg:1 or LM-cfg:2 and FM-cfg:1 in Section 3.2. + + The guidelines (GL-mix) in Section 4.1.1 and in Section 4.2.1 for the + IPv6 nodes for a network or network slice supporting a mix of flows + requiring and not requiring IP mobility support apply here. In + addition, the following are required. + + GL-switch:1 The location management provides information about which + IP prefix from an AR in the original network is being + used by a flow in which AR in a new network. Such + information needs to be deleted or updated when such + flows have closed so that the IP prefix is no longer + used in a different network. The LM behaviors are + described in Section 3.2.1. + + GL-switch:2 The FM functions are implemented through the DHCPv6-PD + protocol. Here the anchor behaviors to properly forward + the packets for a flow as described in the FM behaviors + and mobility message parameters in Section 3.2.2 FM- + path, FM-path-tbl, FM-DPA, FM-DPA-tbl are realized by + changing the anchor with DHCPv6-PD and also by reverting + such changes later after the application has already + closed and when the DHCPv6-PD timer expires. If there + are in-flight packets toward the old anchor while the MN + is moving to the new anchor, it may be necessary to + buffer these packets and then forward to the new anchor + after the old anchor knows that the new anchor is ready. + Such are described in the FM behaviors and mobility + message parameters in Section 3.2.2 FM-buffer. The + anchors may also need to discover each other as + described also in the FM behaviors and mobility message + parameters (FM-find). + + GL-switch:3 The security management function in the anchor node at a + new network must allow to assign the original IP prefix/ + address used by the mobile node at the previous + (original) network. As the assigned original IP prefix/ + address is to be used in the new network, the security + management function in the anchor node must allow to + advertise the prefix of the original IP address and also + allow the mobile node to send and receive data packets + with the original IP address. + + GL-switch:4 The security management function in the mobile node must + allow to configure the original IP prefix/address used + at the previous (original) network when the original IP + prefix/address is assigned by the anchor node in the new + network. The security management function in the mobile + node also allows to use the original IP address for the previous flow in the new network. -4.2.1. Centralized control plane +5.2. IP Prefix/Address Anchor Switching for Flat Network with + Centralized Control Plane An example of IP prefix anchor switching is in the case where Net1 and Net2 both belong to the same operator network with separation of control and data planes ([I-D.liu-dmm-deployment-scenario] and [I-D.matsushima-stateless-uplane-vepc]), where the controller may send to the switches/routers the updated information of the forwarding tables with the IP address anchoring of the original IP prefix/address at AR1 moved to AR2 in the new network. That is, the IP address anchoring in the original network which was advertising the prefix will need to move to the new network. As the anchoring in the new network advertises the prefix of the original IP address in the new network, the forwarding tables will be updated so that packets of the flow will be forwarded according to the updated - forwarding tables. The configuration in Figures 1(a) and 1(b) in + forwarding tables. The configurations in Figures 1(a) and 1(b) in Section 3.1 for which FM-CP and LM are centralized and FM-DP's are - distributed. applies here. Figure 7 shows its implementation where - LM is a binding between the original IP prefix/address of the flow - and the IP address of the new DPA, whereas FM uses the DHCPv6-PD + distributed apply here. Figure 8 shows its implementation where LM + is a binding between the original IP prefix/address of the flow and + the IP address of the new DPA, whereas FM uses the DHCPv6-PD protocol. Net1 Net2 +----------------------------------------------------------------------+ | CPA: | | LM:IP1<-->IPa2 | | FM-CP | +----------------------------------------------------------------------+ +---------------+ +---------------+ @@ -788,29 +1345,30 @@ |DPA(IPa1): | |DPA(IPa2): | |anchors IP1 | move |anchors IP2,IP1| |FM:DHCPv6-PD | =======> |FM:DHCPv6-PD | +---------------+ +---------------+ +...............+ +---------------+ .MN(IP1) . move |MN(IP2,IP1) | .flow(IP1,...) . =======> |flow(IP1,...) | +...............+ +---------------+ - Figure 7. IP prefix/address anchor switching to the new network with + Figure 8. IP prefix/address anchor switching to the new network with with LM and FM-CP in a centralized control plane whereas the FM-DP's are distributed. - The call flow in Figure 8 shows that MN is allocated HNP1 when it - attaches to the p-AR. A flow running in MN may or may not need IP - mobility. If it does, it may continue to use the previous IP prefix. - If it does not, it may use a new IP prefix allocated from the new - network. + The example call flow in Figure 9 shows that MN is allocated HNP1 + when it attaches to the p-AR. A flow running in MN and needing IP + mobility may continue to use the previous IP prefix by moving the + anchoring of the IP prefix to the new network. Yet a new flow to be + initiated in the new network may simply use a new IP prefix allocated + from the new network. MN p-AR n-AR DHCP Servers CN |MN attaches to p-AR: | | | | |acquire MN-ID and profile | | | |--RS---------------->| | | | |<----------RA(HNP1)--| | | | | | | Allocate MN-HNP1 | IP addr config | | | | | | | | | |<-Flow(IP1,IPcn,...)-+--------------------------------------------->| @@ -836,80 +1394,125 @@ | Flow(IP1,IPcn,...) terminates | | | | | | | | | | DHCPv6-PD timeout | | | | | | | | forwarding table updates | | | | | | | | | | | | |<-new Flow(IP2,IPcn,...)-----------+------------------------------->| | | | | | - Figure 8. DMM solution. MN with flow using IP1 in Net1 continues to + Figure 9. DMM solution. MN with flow using IP1 in Net1 continues to run the flow using IP1 as it moves to Net2. As the MN moves from p-AR to n-AR, the p-AR as a DHCP client may send a DHCP release message to release the HNP1. It is now necessary for n-AR to learn the IP prefix of the MN from the previous network so that it will be possible for Net2 to allocate both the previous network prefix and the new network prefix. The network may learn the previous prefix in different methods. For example, the MN may provide its previous network prefix information by including it to the RS message [I-D.jhlee-dmm-dnpp]. Knowing that MN is using HNP1, the n-AR sends to a DHCP server a DHCPv6-PD request to move the HNP1 to n-AR. The server sends to n-AR - a DHCPv6-PD reply to move the HNP1. Then BGP route updates will take - place here. + a DHCPv6-PD reply to move the HNP1. Then forwarding tables updates + will take place here. In addition, the MN also needs a new HNP in the new network. The n-AR may now send RA to n-AR, with prefix information that includes HNP1 and HNP2. The MN may then continue to use IP1. In addition, the MN is allocated the prefix HNP2 with which it may configure its IP addresses. Now for flows using IP1, packets destined to IP1 will be forwarded to the MN via n-AR. As such flows have terminated and DHCP-PD has timed out, HNP1 goes back to Net1. MN will then be left with HNP2 only, which it will use when it now starts a new flow. - The anchor behavior to properly forward the packets for a flow as - described in the FM behaviors and information elements (FM:3) in - Section 3.2.2 is realized by changing the anchor with DHCPv6-PD and - undoing such changes later when its timer expires and the application - has already closed. With the anchors being separated in control and - data planes with LMs and FM-CP centralized in the same control plane, - messaging between anchors and the discovery of anchors become - internal to the control plane. However, the centralized FM-CP needs - to communicate with the distributed FM-DP as described as described - in the FM behaviors and information elements (FM:5). Such may be - realized by the appropriate messages in [I-D.ietf-dmm-fpc-cpdp]. - Again, if there are in-flight packets toward the old anchor while the - MN is moving to the new anchor, it may be necessary to buffer these - packets and then forward to the new anchor after the old anchor knows - that the new anchor is ready. The corresponding FM behaviors and - information elements (FM:6) are however realized by the internal - behavior in the control plane together with signaling between the - control plane and distributed data plane. +5.2.1. Additional Guidelines for IPv6 Nodes: Switching Anchor with + Centralized CP -4.2.2. Hierarchical network + The configuration guideline for a flat network or network slice with + centralized control plane and supporting a mix of flows requiring and + not requiring IP mobility support is: + + GL-cfg:4 Multipel instances of DPAs (at access routers) which are + providing IP prefix to the MNs are needed to provide + distributed anchoring according to Figure 1(a) or + Figure 1(b)in Section 3.1 with centralized control plane + for a flat network. + + The appropriate IPv6 nodes (CPA, DPA) are to be implemented + the mobility functions LM and FM as described respectively + in LM-cfg:1 or LM-cfg:2 and FM-cfg:1 in Section 3.2. + + The guidelines (GL-mix) in Section 4.1.1 and in Section 4.2.1 for the + IPv6 nodes for a network or network slice supporting a mix of flows + requiring and not requiring IP mobility support apply here. The + guidelines (GL-mix) in Section 5.1.1 also apply here. In addition, + the following are required. + + GL-switch:5 The anchor behavior to properly forward the packets for + a flow as described in the FM behaviors and mobility + message parameters in Section 3.2.2 FM-path, FM-path- + tbl, FM-DPA, FM-DPA-tbl is realized by changing the + anchoring with DHCPv6-PD and undoing such changes later + when its timer expires and the application has already + closed. With the anchors being separated in control and + data planes with LMs and FM-CP centralized in the same + control plane, messaging between anchors and the + discovery of anchors become internal to the control + plane as described in Section 3.2.2 FM-cpdp. However, + the centralized FM-CP needs to communicate with the + distributed FM-DP as described as described in the FM + behaviors and mobility message parameters (FM-find). + Such may be realized by the appropriate messages in + [I-D.ietf-dmm-fpc-cpdp]. + + GL-switch:6 It was already mentioned before that, if there are in- + flight packets toward the old anchor while the MN is + moving to the new anchor, it may be necessary to buffer + these packets and then forward to the new anchor after + the old anchor knows that the new anchor is ready Here, + however, the corresponding FM behaviors and mobility + message parameters as described in Section 3.2.2 (FM- + buffer) can be realized by the internal behavior in the + control plane together with signaling between the + control plane and distributed data plane. These + signaling may be realized by the appropriate messages in + [I-D.ietf-dmm-fpc-cpdp]. + +5.3. IP Prefix/Address Anchor Switching for Hierarchical Network The configuration for a hierarchical network is shown in Figures 1(c) - and 1(d) in Section 3.1. With centralized control and with a - centralized anchor, LM, CPA, CPN are co-located at the centralized - control, and there is an AR with the DPA function supporting multiple - forwarding switches (FW's) each with a DPN function. A mobility - event in this configuration involving change of FW but not of AR is - shown in Figure 9. + and 1(d) in Section 3.1. With centralized control plane, CPA and + CPN, with the associated LM and FM-CP are all co-located. There are + multiple DPAs (each with FM-DP) in distributed mobility anchoring. + In the data plane, there are multiple DPNs (each with FM-DP) + hierarchically below each DPA. The DPA at each AR supports + forwarding to the DPN at each of a number of forwarding switches + (FW's). A mobility event in this configuration belonging to + distributed mobility management will be deferred to Section 5.4. - Here the IP prefix allocated to the MN is anchored at the access - router (AR) supporting the old FW to which the MN was originally - attached as well as the new FW to which the MN has moved. + In this distributed mobility configuration, a mobility event + involving change of FW only but not of AR as shown in Figure 10 may + still belong to centralized mobility management and may be supported + using PMIPv6. This configuration of network-based mobility is also + applicable to host-based mobility with the modification for the MN + directly taking the role of DPN and CPN, and the corresponding + centralized mobility event may be supported using MIPv6. + + In Figure 10, the IP prefix allocated to the MN is anchored at the + access router (AR) supporting indirection to the old FW to which the + MN was originally attached as well as to the new FW to which the MN + has moved. The realization of LM may be the binding between the IP prefix/ address of the flow used by the MN and the IP address of the DPN to which MN has moved. The implementation of FM to enable change of FW without changing AR may be accomplished using tunneling between the AR and the FW as described in [I-D.korhonen-dmm-local-prefix] and in [I-D.templin-aerolink] or using some other L2 mobility mechanism. Net1 Net2 +----------------------------------------------------------------------+ @@ -930,54 +1533,78 @@ |FW1 | |FW2 | +---------------+ move +---------------+ |DPN(IPn1): | =======> |DPN(IPn2): | +---------------+ +---------------+ +...............+ +---------------+ .MN(IP1) . move |MN(IP2) | .flow(IP1,...) . =======> |flow(IP1,...) | +...............+ +---------------+ - Figure 9. Mobility without involving change of IP anchoring in a - network with hierarchy in which the IP prefix allocated to the MN is - anchored at an Edge Router supporting multiple access routers to - which the MN may connect. + Figure 10. Mobility without involving change of IP anchoring in a + network in which the IP prefix allocated to the MN is anchored at an + AR which is hierarchically above multiple FWs to which the MN may + connect. - Here, the LM behaviors and information elements described in - Section 3.2.1 provides information of which IP prefix from its FW - needs to be used by a flow using which new FW. The anchor behaviors - to properly forward the packets of a flow described in the FM - behaviors and information elements (FM:3) may be realized with PMIPv6 - protocol ([I-D.korhonen-dmm-local-prefix]) or with AERO protocol - ([I-D.templin-aerolink]) to tunnel between the AR and the FW. +5.3.1. Additional Guidelines for IPv6 Nodes: No Anchoring Change with + Hierarchical Network -4.2.3. Hierarchical network with anchoring change + The configuration guideline ( ) for a hierarchical network or network + slice with centralized control plane and supporting a mix of flows + requiring and not requiring IP mobility support is: - The configuration for a hierarchical network is still shown in - Figures 1(c) and 1(d) in Section 3.1. Again, with centralized - control and with a centralized anchor, LM, CPA, CPN are co-located at - the centralized control, and there is an AR with the DPA function - supporting multiple forwarding switches (FW's) each with a DPN - function. However, the mobility event involving change of FW may - also involve a change of AR. Such configuration is shown in - Figure 10. + GL-cfg:5 Multipel instances of DPAs (at access routers) which are + providing IP prefix to the MNs are needed to provide + distributed anchoring according to Figure 2(a) or + Figure 2(b)in Section 3.1.2 with centralized control plane + for a hierarchical network. - This deployment case involves both a change of anchor from AR1 to AR2 - and a network hierarchy AR-FW. It can be realized by a combination - of changing the IP prefix/address anchoring from AR1 to AR2 with the - mechanism as described in Section 4.2.1 and then forwarding the - packets with network hierarchy AR-FW as described in Section 4.2.2. + The appropriate IPv6 nodes (CPA, DPA) are to be implemented + the mobility functions LM and FM as described respectively + in LM-cfg:3 or LM-cfg:4 and FM-cfg:2 in Section 3.2. - To change AR, AR1 acting as a DHCP-PD client may exchange message - with the DHCP server to release the prefix IP1. Meanwhile, AR2 - acting as a DHCP-PD client may exchange message with the DHCP server - to delegate the prefix IP1 to AR2. + Even when the mobility event does not involve change of anchor, it is + still necessary to distinguish whether a flow needs IP mobility + support. + + The GL-mix guidelines in Section 4.1.1 and in Section 4.2.1 for the + IPv6 nodes for a network or network slice supporting a mix of flows + requiring and not requiring IP mobility support apply here. The + guidelines (GL-switch) in Section 5.1.1 and in Section 5.2.1 also + apply here. In addition, the following are required. + + GL-switch:7 Here, the LM behaviors and mobility message parameters + described in Section 3.2.1 provides information of which + IP prefix from its FW needs to be used by a flow using + which new FW. The anchor behaviors to properly forward + the packets of a flow described in the FM behaviors and + mobility message parameters (FM-path, FM-path-ind, FM- + cpdp in Section 3.2.2) may be realized with PMIPv6 + protocol ([I-D.korhonen-dmm-local-prefix]) or with AERO + protocol ([I-D.templin-aerolink]) to tunnel between the + AR and the FW. + +5.4. IP Prefix/Address Anchor Switching for Hierarchical Network + + The configuration for the hierarchical network is again shown in + Figures 1(c) and 1(d) in Section 3.1. Again, with centralized + control plane, CPA and CPN, with the associated LM and FM-CP are all + co-located. There are multiple DPAs (each with FM-DP) in distributed + mobility anchoring. In the data plane, there are multiple DPNs (each + with FM-DP) hierarchically below each DPA. The DPA at each AR + supports forwarding to the DPN at each of a number of forwarding + switches (FW's). + + A distributed mobility event in this configuration involves change + from a previous DPN which is hierarchically under the previous DPA to + a new DPN which is hierarchically under a new DPA. Such an event + involving change of both DPA and DPN is shown in Figure 11. Net1 Net2 +----------------------------------------------------------------------+ | CPA,CPN: | | LM:IP1<-->IPa2,IPn2 | | FM-CP | +----------------------------------------------------------------------+ +---------------+ |Aggregate Point| @@ -997,50 +1624,84 @@ |FW1 | |FW2 | +---------------+ move +---------------+ |DPN(IPn1): | =======> |DPN(IPn2): | +---------------+ +---------------+ +...............+ +---------------+ .MN(IP1) . move |MN(IP2,IP1) | .flow(IP1,...) . =======> |flow(IP1,...) | +...............+ +---------------+ - Figure 10. Mobility involving change of IP anchoring in a network + Figure 11. Mobility involving change of IP anchoring in a network with hierarchy in which the IP prefix allocated to the MN is anchored at an Edge Router supporting multiple access routers to which the MN may connect. -5. Security Considerations + This deployment case involves both a change of anchor from AR1 to AR2 + and a network hierarchy AR-FW. It can be realized by a combination + of changing the IP prefix/address anchoring from AR1 to AR2 with the + mechanism as described in Section 5.2 and then forwarding the packets + with network hierarchy AR-FW as described in Section 5.3. + + To change AR, AR1 acting as a DHCP-PD client may exchange message + with the DHCP server to release the prefix IP1. Meanwhile, AR2 + acting as a DHCP-PD client may exchange message with the DHCP server + to delegate the prefix IP1 to AR2. + +5.4.1. Additional Guidelines for IPv6 Nodes: Switching Anchor with + Hierarchical Network + + The configuration guideline (GL-cfg) for a hierarchical network or + network slice with centralized control plane described in + Section 5.3.1 apply here. + + The GL-mix guidelines in Section 4.1.1 and in Section 4.2.1 for the + IPv6 nodes for a network or network slice supporting a mix of flows + requiring and not requiring IP mobility support apply here. + + The guidelines (GL-switch) in Section 5.1.1 and in Section 5.2.1 also + apply here to change the anchoring of the IP prefix/address with a + centralized control plane. + + In addition, the guideline for indirection between the new DPA and + the new DPN as described in Section 5.3.1 apply here. + +6. Security Considerations TBD -6. IANA Considerations +7. IANA Considerations This document presents no IANA considerations. -7. Contributors +8. Contributors This document has benefited from other work on mobility solutions using BGP update, on mobility support in SDN network, on providing mobility support only when needed, and on mobility support in enterprise network. These work have been referenced. While some of these authors have taken the work to jointly write this document, others have contributed at least indirectly by writing these drafts. The latter include Philippe Bertin, Dapeng Liu, Satoru Matushima, Peter McCann, Pierrick Seite, Jouni Korhonen, and Sri Gundavelli. - Valuable comments have also been received from John Kaippallimil, + Valuable comments have also been received from John Kaippallimalil, ChunShan Xiong, and Dapeng Liu. -8. References +9. References -8.1. Normative References +9.1. Normative References + + [I-D.ietf-dmm-deployment-models] + Gundavelli, S. and S. Jeon, "DMM Deployment Models and + Architectural Considerations", draft-ietf-dmm-deployment- + models-00 (work in progress), August 2016. [I-D.ietf-dmm-fpc-cpdp] Liebsch, M., Matsushima, S., Gundavelli, S., Moses, D., and L. Bertz, "Protocol for Forwarding Policy Configuration (FPC) in DMM", draft-ietf-dmm-fpc-cpdp-03 (work in progress), March 2016. [I-D.ietf-dmm-ondemand-mobility] Yegin, A., Moses, D., Kweon, K., Lee, J., and J. Park, "On Demand Mobility Management", draft-ietf-dmm-ondemand- @@ -1083,101 +1744,114 @@ Anchoring", draft-seite-dmm-dma-07 (work in progress), February 2014. [I-D.sijeon-dmm-deployment-models] Jeon, S. and Y. Kim, "Deployment Models for Distributed Mobility Management", draft-sijeon-dmm-deployment- models-03 (work in progress), July 2016. [I-D.templin-aerolink] Templin, F., "Asymmetric Extended Route Optimization - (AERO)", draft-templin-aerolink-70 (work in progress), - July 2016. - - [I-D.wt-dmm-deployment-models] - Gundavelli, S., "DMM Deployment Models and Architectural - Considerations", draft-wt-dmm-deployment-models-00 (work - in progress), April 2016. + (AERO)", draft-templin-aerolink-71 (work in progress), + September 2016. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . + [RFC3753] Manner, J., Ed. and M. Kojo, Ed., "Mobility Related + Terminology", RFC 3753, DOI 10.17487/RFC3753, June 2004, + . + [RFC5213] Gundavelli, S., Ed., Leung, K., Devarapalli, V., Chowdhury, K., and B. Patil, "Proxy Mobile IPv6", RFC 5213, DOI 10.17487/RFC5213, August 2008, . [RFC6275] Perkins, C., Ed., Johnson, D., and J. Arkko, "Mobility Support in IPv6", RFC 6275, DOI 10.17487/RFC6275, July 2011, . + [RFC7077] Krishnan, S., Gundavelli, S., Liebsch, M., Yokota, H., and + J. Korhonen, "Update Notifications for Proxy Mobile IPv6", + RFC 7077, DOI 10.17487/RFC7077, November 2013, + . + [RFC7333] Chan, H., Ed., Liu, D., Seite, P., Yokota, H., and J. Korhonen, "Requirements for Distributed Mobility Management", RFC 7333, DOI 10.17487/RFC7333, August 2014, . [RFC7429] Liu, D., Ed., Zuniga, JC., Ed., Seite, P., Chan, H., and CJ. Bernardos, "Distributed Mobility Management: Current Practices and Gap Analysis", RFC 7429, DOI 10.17487/RFC7429, January 2015, . -8.2. Informative References +9.2. Informative References [Paper-Distributed.Mobility] Lee, J., Bonnin, J., Seite, P., and H. Chan, "Distributed IP Mobility Management from the Perspective of the IETF: Motivations, Requirements, Approaches, Comparison, and Challenges", IEEE Wireless Communications, October 2013. [Paper-Distributed.Mobility.PMIP] Chan, H., "Proxy Mobile IP with Distributed Mobility Anchors", Proceedings of GlobeCom Workshop on Seamless Wireless Mobility, December 2010. [Paper-Distributed.Mobility.Review] Chan, H., Yokota, H., Xie, J., Seite, P., and D. Liu, "Distributed and Dynamic Mobility Management in Mobile Internet: Current Approaches and Issues", February 2011. Authors' Addresses - H Anthony Chan + H Anthony Chan (editor) Huawei Technologies 5340 Legacy Dr. Building 3 Plano, TX 75024 USA Email: h.a.chan@ieee.org + Xinpeng Wei Huawei Technologies Xin-Xi Rd. No. 3, Haidian District Beijing, 100095 P. R. China Email: weixinpeng@huawei.com - Jong-Hyouk Lee Sangmyung University - 708 Hannuri Building - Cheonan 330-720 - Korea + 31, Sangmyeongdae-gil, Dongnam-gu + Cheonan 31066 + Republic of Korea Email: jonghyouk@smu.ac.kr Seil Jeon Sungkyunkwan University 2066 Seobu-ro, Jangan-gu Suwon, Gyeonggi-do - Korea + Republic of Korea - Email: seiljeon@gmail.com + Email: seiljeon@skku.edu + + Alexandre Petrescu + CEA, LIST + CEA Saclay + Gif-sur-Yvette, Ile-de-France 91190 + France + + Phone: +33169089223 + Email: Alexandre.Petrescu@cea.fr Fred L. Templin Boeing Research and Technology P.O. Box 3707 Seattle, WA 98124 USA Email: fltemplin@acm.org