[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: 00 01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22 23
24 25 26 RFC 4566
Network Working Group M. Handley
Internet-Draft UCL
Obsoletes: 2327, 3266 (if V. Jacobson
approved) Packet Design
Expires: December 10, 2004 C. Perkins
University of Glasgow
June 11, 2004
SDP: Session Description Protocol
draft-ietf-mmusic-sdp-new-18.txt
Status of this Memo
By submitting this Internet-Draft, I certify that any applicable
patent or other IPR claims of which I am aware have been disclosed,
and any of which I become aware will be disclosed, in accordance with
RFC 3668.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at http://
www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 10, 2004.
Copyright Notice
Copyright (C) The Internet Society (2004). All Rights Reserved.
Abstract
This memo defines the Session Description Protocol (SDP). SDP is
intended for describing multimedia sessions for the purposes of
session announcement, session invitation, and other forms of
multimedia session initiation.
Handley, et al. Expires December 10, 2004 [Page 1]
Internet-Draft SDP June 2004
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Glossary of Terms . . . . . . . . . . . . . . . . . . . . . 3
3. Examples of SDP Usage . . . . . . . . . . . . . . . . . . . 3
3.1 Multicast Session Announcement . . . . . . . . . . . . . . 3
3.2 Session Initiation . . . . . . . . . . . . . . . . . . . . 4
3.3 Streaming media . . . . . . . . . . . . . . . . . . . . . 4
3.4 Email and the World Wide Web . . . . . . . . . . . . . . . 4
4. Requirements and Recommendations . . . . . . . . . . . . . . 5
4.1 Media Information . . . . . . . . . . . . . . . . . . . . 5
4.2 Timing Information . . . . . . . . . . . . . . . . . . . . 6
4.3 Private Sessions . . . . . . . . . . . . . . . . . . . . . 6
4.4 Obtaining Further Information about a Session . . . . . . 6
4.5 Categorisation . . . . . . . . . . . . . . . . . . . . . . 6
4.6 Internationalization . . . . . . . . . . . . . . . . . . . 7
5. SDP Specification . . . . . . . . . . . . . . . . . . . . . 7
5.1 Protocol Version ("v=") . . . . . . . . . . . . . . . . . 9
5.2 Origin ("o=") . . . . . . . . . . . . . . . . . . . . . . 10
5.3 Session Name ("s=") . . . . . . . . . . . . . . . . . . . 11
5.4 Session Information ("i=") . . . . . . . . . . . . . . . . 11
5.5 URI ("u=") . . . . . . . . . . . . . . . . . . . . . . . . 11
5.6 Email Address and Phone Number ("e=" and "p=") . . . . . . 11
5.7 Connection Data ("c=") . . . . . . . . . . . . . . . . . . 12
5.8 Bandwidth ("b=") . . . . . . . . . . . . . . . . . . . . . 14
5.9 Timing ("t=") . . . . . . . . . . . . . . . . . . . . . . 15
5.10 Repeat Times ("r=") . . . . . . . . . . . . . . . . . . 16
5.11 Time Zones ("z=") . . . . . . . . . . . . . . . . . . . 17
5.12 Encryption Keys ("k=") . . . . . . . . . . . . . . . . . 18
5.13 Attributes ("a=") . . . . . . . . . . . . . . . . . . . 19
5.14 Media Descriptions ("m=") . . . . . . . . . . . . . . . 21
6. Suggested Attributes . . . . . . . . . . . . . . . . . . . . 24
7. Communicating Conference Control Policy . . . . . . . . . . 29
8. Security Considerations . . . . . . . . . . . . . . . . . . 30
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . 31
9.1 The "application/sdp" media type . . . . . . . . . . . . . 31
9.2 Registration of Parameters . . . . . . . . . . . . . . . . 32
9.3 Encryption Key Access Methods . . . . . . . . . . . . . . 36
A. SDP Grammar . . . . . . . . . . . . . . . . . . . . . . . . 37
B. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . 42
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.1 Normative References . . . . . . . . . . . . . . . . . . . 42
10.2 Informative References . . . . . . . . . . . . . . . . . . 42
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . 43
Intellectual Property and Copyright Statements . . . . . . . 45
Handley, et al. Expires December 10, 2004 [Page 2]
Internet-Draft SDP June 2004
1. Introduction
[Note to RFC Editor: All references to RFC XXXX should be replaced by
the RFC number of this document, when published.]
When initiating multimedia teleconferences, voice-over-IP calls,
streaming video, or other sessions, there is a requirement to convey
media details, transport addresses, and other session description
metadata to the participants.
SDP provides a standard representation for such information,
irrespective of how that information is transported. SDP is purely a
format for session description - it does not incorporate a transport
protocol, and is intended to use different transport protocols as
appropriate, including the Session Announcement Protocol [8], Session
Initiation Protocol [9], Real-Time Streaming Protocol [10],
electronic mail using the MIME extensions, and the Hypertext
Transport Protocol.
SDP is intended to be general purpose so that it can be used in a
wide range of network environments and applications. However, it is
not intended to support negotiation of session content or media
encodings: this is viewed as outside the scope of session
description.
2. Glossary of Terms
The following terms are used in this document, and have specific
meaning within the context of this document.
Conference: A multimedia conference is a set of two or more
communicating users along with the software they are using to
communicate.
Session: A multimedia session is a set of multimedia senders and
receivers and the data streams flowing from senders to receivers.
A multimedia conference is an example of a multimedia session.
Session Description: A well defined format for conveying sufficient
information to discover and participate in a multimedia session.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [1].
3. Examples of SDP Usage
3.1 Multicast Session Announcement
In order to assist the advertisement of multicast multimedia
Handley, et al. Expires December 10, 2004 [Page 3]
Internet-Draft SDP June 2004
conferences and other multicast sessions, and to communicate the
relevant session setup information to prospective participants, a
distributed session directory may be used. An instance of such a
session directory periodically sends packets containing a description
of the session to a well known multicast group. These advertisements
are received by other session directories such that potential remote
participants can use the session description to start the tools
required to participate in the session.
One protocol commonly used to implement such a distributed directory
is the Session Announcement Protocol, SAP [8]. SDP provides the
recommended session description format for such session
announcements.
3.2 Session Initiation
The Session Initiation Protocol, SIP [9] is an application layer
control protocol for creating, modifying and terminating sessions
such as Internet multimedia conferences, Internet telephone calls and
multimedia distribution. The SIP messages used to create sessions
carry session descriptions which allow participants to agree on a set
of compatible media types. These session descriptions are commonly
formatted using SDP. When used with SIP, the offer/answer model [11]
provides a limited framework for negotiation using SDP.
3.3 Streaming media
The Real Time Streaming Protocol, RTSP [10], is an application-level
protocol for control over the delivery of data with real-time
properties. RTSP provides an extensible framework to enable
controlled, on-demand delivery of real-time data, such as audio and
video. An RTSP client and server negotiate an appropriate set of
parameters for media delivery, partially using SDP syntax to describe
those parameters.
3.4 Email and the World Wide Web
Alternative means of conveying session descriptions include
electronic mail and the World Wide Web. For both email and WWW
distribution, the MIME content type "application/sdp" is used. This
enables the automatic launching of applications for participation in
the session from the WWW client or mail reader in a standard manner.
Note that announcements of multicast sessions made only via email or
the World Wide Web (WWW) do not have the property that the receiver
of a session announcement can necessarily receive the session because
the multicast sessions may be restricted in scope, and access to the
WWW server or reception of email is possible outside this scope.
Handley, et al. Expires December 10, 2004 [Page 4]
Internet-Draft SDP June 2004
Session announcements made using SAP do not suffer from this
mismatch.
4. Requirements and Recommendations
The purpose of SDP is to convey information about media streams in
multimedia sessions to allow the recipients of a session description
to participate in the session. SDP is primarily intended for use in
an internetwork, although it is sufficiently general that it can
describe conferences in other network environments. Media streams can
be many-to-many. The times during which the session is active need
not be continuous.
Thus far, multicast based sessions on the Internet have differed from
many other forms of conferencing in that anyone receiving the traffic
can join the session (unless the session traffic is encrypted). In
such an environment, SDP serves two primary purposes. It is a means
to communicate the existence of a session, and is a means to convey
sufficient information to enable joining and participating in the
session. In a unicast environment, only the latter purpose is likely
to be relevant.
Thus SDP includes:
o Session name and purpose
o Time(s) the session is active
o The media comprising the session
o Information needed to receive those media (addresses, ports,
formats and so on)
As resources necessary to participate in a session may be limited,
some additional information may also be desirable:
o Information about the bandwidth to be used by the conference
o Contact information for the person responsible for the session
In general, SDP must convey sufficient information to enable
applications to join a session (with the possible exception of
encryption keys) and to announce the resources to be used to non-
participants that may need to know.
4.1 Media Information
SDP includes:
o The type of media (video, audio, etc)
o The transport protocol (RTP/UDP/IP, H.320, etc)
o The format of the media (H.261 video, MPEG video, etc)
For an IP multicast session, the following are also conveyed:
o Multicast address for media
o Transport port for media
This address and port are the destination address and destination
Handley, et al. Expires December 10, 2004 [Page 5]
Internet-Draft SDP June 2004
port of the multicast stream, whether being sent, received, or both.
For an IP unicast session, the following are conveyed:
o Remote address for media
o Transport port for media
The semantics of this address and port depend on the media and
transport protocol defined. By default, this is the remote address
and remote port to which data is sent, however some media types may
redefine this behaviour.
4.2 Timing Information
Sessions may either be bounded or unbounded in time. Whether or not
they are bounded, they may be only active at specific times.
SDP can convey:
o An arbitrary list of start and stop times bounding the session
o For each bound, repeat times such as "every Wednesday at 10am for
one hour"
This timing information is globally consistent, irrespective of local
time zone or daylight saving time.
4.3 Private Sessions
It is possible to create both public sessions and private sessions.
SDP itself does not distinguish between these: private sessions are
typically conveyed by encrypting the session description during
distribution. The details of how encryption is performed are
dependent on the mechanism used to convey SDP - e.g. mechanisms are
defined for SDP transported using SAP [8] and SIP [9].
If a session announcement is private it is possible to use that
private announcement to convey encryption keys necessary to decode
each of the media in a conference, including enough information to
know which encryption scheme is used for each media.
4.4 Obtaining Further Information about a Session
A session description should convey enough information to decide
whether or not to participate in a session. SDP may include
additional pointers in the form of Universal Resources Identifiers
(URIs) for more information about the session.
4.5 Categorisation
When many session descriptions are being distributed by SAP, or any
other advertisement mechanism, it may be desirable to filter session
announcements that are of interest from those that are not. SDP
Handley, et al. Expires December 10, 2004 [Page 6]
Internet-Draft SDP June 2004
supports a categorisation mechanism for sessions that is capable of
being automated.
4.6 Internationalization
The SDP specification recommends the use of the ISO 10646 character
sets in the UTF-8 encoding [3] to allow many different languages to
be represented. However, to assist in compact representations, SDP
also allows other character sets such as ISO 8859-1 to be used when
desired. Internationalization only applies to free-text fields
(session name and background information), and not to SDP as a whole.
5. SDP Specification
An SDP session description is denoted by the MIME content type
"application/sdp" (See Section 9).
An SDP session description is entirely textual using the ISO 10646
character set in UTF-8 encoding. SDP field names and attribute names
use only the US-ASCII subset of UTF-8, but textual fields and
attribute values MAY use the full ISO 10646 character set. Field and
attribute values which use the full UTF-8 character set are never
directly compared, hence there is no requirement for UTF-8
normalization. The textual form, as opposed to a binary encoding
such as ASN.1 or XDR, was chosen to enhance portability, to enable a
variety of transports to be used (e.g, session description in a MIME
email message) and to allow flexible, text-based toolkits (e.g., Tcl/
Tk) to be used to generate and to process session descriptions.
However, since SDP may be used in environments where the maximum
permissable size of a session description is limited (e.g. SAP
announcements), the encoding is deliberately compact. Also, since
announcements may be transported via very unreliable means or damaged
by an intermediate caching server, the encoding was designed with
strict order and formatting rules so that most errors would result in
malformed session announcements which could be detected easily and
discarded. This also allows rapid discarding of encrypted session
announcements for which a receiver does not have the correct key.
An SDP session description consists of a number of lines of text of
the form:
<type>=<value>
where <type> MUST be exactly one case-significant character and
<value> is structured text whose format depends on <type>. In
general <value> is either a number of fields delimited by a single
space character, or a free format string. Whitespace MUST NOT be used
either side of the "=" sign.
Handley, et al. Expires December 10, 2004 [Page 7]
Internet-Draft SDP June 2004
An SDP session description consists of a session-level section
followed by zero or more media-level sections. The session-level
part starts with a "v=" line and continues to the first media-level
section. The media description starts with an "m=" line and
continues to the next media description or end of the whole session
description. In general, session-level values are the default for
all media unless overridden by an equivalent media-level value.
Some lines in each description are REQUIRED and some are OPTIONAL but
all MUST appear in exactly the order given here (the fixed order
greatly enhances error detection and allows for a simple parser).
OPTIONAL items are marked with a "*".
Session description
v= (protocol version)
o= (owner/creator and session identifier).
s= (session name)
i=* (session information)
u=* (URI of description)
e=* (email address)
p=* (phone number)
c=* (connection information - not required if included in
all media)
b=* (zero or more bandwidth information lines)
One or more time descriptions (see below)
z=* (time zone adjustments)
k=* (encryption key)
a=* (zero or more session attribute lines)
Zero or more media descriptions (see below)
Time description
t= (time the session is active)
r=* (zero or more repeat times)
Media description
m= (media name and transport address)
i=* (media title)
c=* (connection information - optional if included at
session-level)
b=* (zero or more bandwidth information lines)
k=* (encryption key)
a=* (zero or more media attribute lines)
The set of type letters is deliberately small and not intended to be
extensible -- an SDP parser MUST completely ignore any session
description that contains a type letter that it does not understand.
The attribute mechanism ("a=" described below) is the primary means
for extending SDP and tailoring it to particular applications or
Handley, et al. Expires December 10, 2004 [Page 8]
Internet-Draft SDP June 2004
media. Some attributes (the ones listed in Section 6 of this memo)
have a defined meaning, but others may be added on an application-,
media- or session-specific basis. An SDP parser MUST ignore any
attribute it doesn't understand.
An SDP session description may contain URIs which reference external
content in the "u=", "k=" and "a=" lines. These URIs may be
dereferenced in some cases, making the session description non-self
contained.
The connection ("c=") and attribute ("a=") information in the
session-level section applies to all the media of that session unless
overridden by connection information or an attribute of the same name
in the media description. For instance, in the example below, each
media behaves as if it were given a "recvonly" attribute.
An example SDP description is:
v=0
o=jdoe 2890844526 2890842807 IN IP4 10.47.16.5
s=SDP Seminar
i=A Seminar on the session description protocol
u=http://www.example.com/seminars/sdp.pdf
e=j.doe@example.com (Jane Doe)
c=IN IP4 224.2.17.12/127
t=2873397496 2873404696
a=recvonly
m=audio 49170 RTP/AVP 0
m=video 51372 RTP/AVP 31
m=application 32416 udp wb
a=orient:portrait
Text fields such as the session name and information are octet
strings which may contain any octet with the exceptions of 0x00
(Nul), 0x0a (ASCII newline) and 0x0d (ASCII carriage return). The
sequence CRLF (0x0d0a) is used to end a record, although parsers
SHOULD be tolerant and also accept records terminated with a single
newline character. If the "a=charset" attribute is not present,
these octet strings MUST be interpreted as containing ISO-10646
characters in UTF-8 encoding (the presence of the "a=charset"
attribute MAY force some fields to be interpreted differently).
5.1 Protocol Version ("v=")
v=0
The "v=" field gives the version of the Session Description Protocol.
This memo defines version 0. There is no minor version number.
Handley, et al. Expires December 10, 2004 [Page 9]
Internet-Draft SDP June 2004
5.2 Origin ("o=")
o=<username> <sess-id> <sess-version> <nettype> <addrtype>
<unicast-address>
The "o=" field gives the originator of the session (her username and
the address of the user's host) plus a session identifier and version
number:
<username> is the user's login on the originating host, or it is "-"
if the originating host does not support the concept of user ids.
The <username> MUST NOT contain spaces.
<sess-id> is a numeric string such that the tuple of <username>,
<sess-id>, <nettype>, <addrtype> and <unicast-address> form a
globally unique identifier for the session. The method of
<sess-id> allocation is up to the creating tool, but it has been
suggested that a Network Time Protocol (NTP) format timestamp be
used to ensure uniqueness [7].
<sess-version> is a version number for this session description. Its
usage is up to the creating tool, so long as <sess-version> is
increased when a modification is made to the session data. Again,
it is RECOMMENDED that an NTP format timestamp is used.
<nettype> is a text string giving the type of network. Initially "IN"
is defined to have the meaning "Internet", but other values MAY be
registered in future (see Section 9).
<addrtype> is a text string giving the type of the address that
follows. Initially "IP4" and "IP6" are defined, but other values
MAY be registered in future (see Section 9).
<unicast-address> is the address of the machine from which the
session was created. For an address type of IP4, this is either
the fully-qualified domain name of the machine, or the
dotted-decimal representation of the IP version 4 address of the
machine. For an address type of IP6, this is either the
fully-qualified domain name of the machine, or the compressed
textual representation of the IP version 6 address of the machine.
For both IP4 and IP6, the fully-qualified domain name is the form
that SHOULD be given unless this is unavailable, in which case the
globally unique address MAY be substituted. A local IP address
MUST NOT be used in any context where the SDP description might
leave the scope in which the address is meaningful.
In general, the "o=" field serves as a globally unique identifier for
this version of this session description, and the subfields excepting
the version taken together identify the session irrespective of any
modifications.
Handley, et al. Expires December 10, 2004 [Page 10]
Internet-Draft SDP June 2004
5.3 Session Name ("s=")
s=<session name>
The "s=" field is the textual session name. There MUST be one and
only one "s=" field per session description. The "s=" field MUST NOT
be empty and SHOULD contain ISO 10646 characters (but see also the
"a=charset" attribute). If a session has no meaningful name, the
value "s= " SHOULD be used (i.e. a single space as the session name).
5.4 Session Information ("i=")
i=<session description>
The "i=" field provides textual information about the session. There
may be at most one session-level "i=" field per session description,
and at most one "i=" field per media. If the "a=charset" attribute is
present, it specifies the character set used in the "i=" field. If
the "a=charset" attribute is not present, the "i=" field MUST contain
ISO 10646 characters in UTF-8 encoding.
A single "i=" field MAY also be used for each media definition. In
media definitions, "i=" fields are primarily intended for labeling
media streams. As such, they are most likely to be useful when a
single session has more than one distinct media stream of the same
media type. An example would be two different whiteboards, one for
slides and one for feedback and questions.
5.5 URI ("u=")
u=<uri>
A URI is a Universal Resource Identifier as used by WWW clients [4].
The URI should be a pointer to additional information about the
conference. This field is OPTIONAL, but if it is present it MUST be
specified before the first media field. No more than one URI field is
allowed per session description.
5.6 Email Address and Phone Number ("e=" and "p=")
e=<email-address>
p=<phone-number>
The "e=" and "p=" lines specify contact information for the person
responsible for the conference. This is not necessarily the same
person that created the conference announcement.
Inclusion of an email address or phone number is OPTIONAL. Note that
Handley, et al. Expires December 10, 2004 [Page 11]
Internet-Draft SDP June 2004
the previous version of SDP specified that either an email field or a
phone field MUST be specified, but this was widely ignored. The
change brings the specification into line with common usage.
If the email addres or phone number are present, they MUST be
specified before the first media field. More than one email or phone
field can be given for a session description.
Phone numbers SHOULD be given in the form of an international public
telecommunication number (see ITU-T Recommendation E.164) preceded by
a "+". Spaces and hyphens may be used to split up a phone field to
aid readability if desired. For example:
p=+44-171-380-7777 or p=+1 617 555 6011
Both email addresses and phone numbers can have an OPTIONAL free text
string associated with them, normally giving the name of the person
who may be contacted. This MUST be enclosed in parenthesis if it is
present. For example:
e=j.doe@example.com (Jane Doe)
The alternative RFC 2822 name quoting convention is also allowed for
both email addresses and phone numbers. For example:
e=Jane Doe <j.doe@example.com>
The free text string SHOULD be in the ISO-10646 character set with
UTF-8 encoding, or alternatively in ISO-8859-1 or other encodings if
the appropriate session-level "a=charset" attribute is set.
5.7 Connection Data ("c=")
c=<nettype> <addrtype> <connection-address>
The "c=" field contains connection data.
A session description MUST contain either at least one "c=" field in
each media description or a single "c=" field at the session level.
It MAY contain a single session-level "c=" field and additional "c="
field(s) per media description, in which case the per-media values
override the session-level settings for the respective media.
The first sub-field ("<nettype>") is the network type, which is a
text string giving the type of network. Initially "IN" is defined to
have the meaning "Internet", but other values MAY be registered in
the future (see Section 9).
Handley, et al. Expires December 10, 2004 [Page 12]
Internet-Draft SDP June 2004
The second sub-field ("<addrtype>") is the address type. This allows
SDP to be used for sessions that are not IP based. Currently only IP4
and IP6 are defined, but other values MAY be registered in the future
(see Section 9).
The third sub-field ("<connection-address>") is the connection
address. OPTIONAL sub-fields MAY be added after the connection
address depending on the value of the <addrtype> field.
When the <addrtype> is IP4 and IP6, the connection address is defined
as follows:
o If the session is multicast, the connection address will be an IP
multicast group address. If the session is not multicast, then
the connection address contains the unicast IP address of the
expected data source or data relay or data sink as determined by
additional attribute fields. It is not expected that unicast
addresses will be given in a session description that is
communicated by a multicast announcement, though this is not
prohibited.
o Conferences using an IPv4 multicast connection address MUST also
have a time to live (TTL) value present in addition to the
multicast address. The TTL and the address together define the
scope with which multicast packets sent in this conference will be
sent. TTL values MUST be in the range 0-255.
The TTL for the session is appended to the address using a slash as a
separator. An example is:
c=IN IP4 224.2.36.42/127
IPv6 multicast does not use TTL scoping, and hence the TTL value MUST
NOT be present for IPv6 multicast. It is expected that IPv6 scoped
addresses will be used to limit the scope of conferences.
Hierarchical or layered encoding schemes are data streams where the
encoding from a single media source is split into a number of layers.
The receiver can choose the desired quality (and hence bandwidth) by
only subscribing to a subset of these layers. Such layered encodings
are normally transmitted in multiple multicast groups to allow
multicast pruning. This technique keeps unwanted traffic from sites
only requiring certain levels of the hierarchy. For applications
requiring multiple multicast groups, we allow the following notation
to be used for the connection address:
<base multicast address>[/<ttl>]/<number of addresses>
If the number of addresses is not given it is assumed to be one.
Handley, et al. Expires December 10, 2004 [Page 13]
Internet-Draft SDP June 2004
Multicast addresses so assigned are contiguously allocated above the
base address, so that, for example:
c=IN IP4 224.2.1.1/127/3
would state that addresses 224.2.1.1, 224.2.1.2 and 224.2.1.3 are to
be used at a TTL of 127. This is semantically identical to including
multiple "c=" lines in a media description:
c=IN IP4 224.2.1.1/127
c=IN IP4 224.2.1.2/127
c=IN IP4 224.2.1.3/127
Similarly, an IPv6 example would be:
c=IN IP6 FF15::101/3
which is semantically equivalent to:
c=IN IP6 FF15::101
c=IN IP6 FF15::102
c=IN IP6 FF15::103
(remembering that the TTL field is not present in IPv6 multicast).
Multiple addresses or "c=" lines MAY be specified on a per-media
basis only if they provide multicast addresses for different layers
in a hierarchical or layered encoding scheme. They MUST NOT be
specified for a session-level "c=" field.
The slash notation described above MUST NOT be used for IP unicast
addresses.
5.8 Bandwidth ("b=")
b=<bwtype>:<bandwidth>
This OPTIONAL field denotes the proposed bandwidth to be used by the
session or media. The <bwtype> is an alphanumeric modifier giving
the meaning of the <bandwidth> figure. Two values are initially
defined, but other values MAY be registered in future (see Section
9):
CT If the bandwidth of a session or media in a session is different
from the bandwidth implicit from the scope, a "b=CT:..." line
SHOULD be supplied for the session giving the proposed upper limit
to the bandwidth used. The primary purpose of this is to give an
approximate idea as to whether two or more sessions can co-exist
Handley, et al. Expires December 10, 2004 [Page 14]
Internet-Draft SDP June 2004
simultaneously. When using the CT modifier with RTP, if several
RTP sessions are part of the conference, the conference total
refers to total bandwidth of all RTP sessions.
AS The bandwidth is interpreted to be application-specific (it will
be the application's concept of maximum bandwidth). Normally this
will coincide with what is set on the application's "maximum
bandwidth" control if applicable. For RTP based applications, AS
gives the RTP "session bandwidth" as defined in section 6.2 of
[12].
Note that CT gives a total bandwidth figure for all the media at all
sites. AS gives a bandwidth figure for a single media at a single
site, although there may be many sites sending simultaneously.
A prefix "X-" is defined for <bwtype> names. This is intended for
experimental purposes only. For example:
b=X-YZ:128
Use of the "X-" prefix is NOT RECOMMENDED: instead new modifiers
SHOULD be registered with IANA in the standard namespace. SDP parsers
MUST ignore bandwidth fields with unknown modifiers. Modifiers MUST
be alpha-numeric and, although no length limit is given, they are
recommended to be short.
The <bandwidth> is in kilobits per second by default. Modifiers MAY
specify that alternative units are to be used (the modifiers defined
in this memo use the default units).
5.9 Timing ("t=")
t=<start-time> <stop-time>
The "t=" lines specify the start and stop times for a session.
Multiple "t=" lines MAY be used if a session is active at multiple
irregularly spaced times; each additional "t=" lines specifies an
additional period of time for which the session will be active. If
the session is active at regular times, an "r=" line (see below)
should be used in addition to, and following, a "t=" line - in which
case the "t=" line specifies the start and stop times of the repeat
sequence.
The first and second sub-fields give the start and stop times for the
session respectively. These values are the decimal representation of
Network Time Protocol (NTP) time values in seconds [7]. To convert
these values to UNIX time, subtract decimal 2208988800.
NTP timestamps are 64 bit values which wrap sometime in the year
Handley, et al. Expires December 10, 2004 [Page 15]
Internet-Draft SDP June 2004
2036. Since SDP uses an arbitrary length decimal representation,
this should not cause an issue (SDP timestamps will continue counting
seconds since 1900, NTP will use the value modulo the 64 bit limit).
If the <stop-time> is set to zero, then the session is not bounded,
though it will not become active until after the <start-time>. If
the <start-time> is also zero, the session is regarded as permanent.
User interfaces SHOULD strongly discourage the creation of unbounded
and permanent sessions as they give no information about when the
session is actually going to terminate, and so make scheduling
difficult.
The general assumption may be made, when displaying unbounded
sessions that have not timed out to the user, that an unbounded
session will only be active until half an hour from the current time
or the session start time, whichever is the later. If behaviour
other than this is required, an end-time should be given and modified
as appropriate when new information becomes available about when the
session should really end.
Permanent sessions may be shown to the user as never being active
unless there are associated repeat times which state precisely when
the session will be active. In general, permanent sessions SHOULD
NOT be created for any session expected to have a duration of less
than 2 months, and should be discouraged for sessions expected to
have a duration of less than 6 months.
5.10 Repeat Times ("r=")
r=<repeat-interval> <active duration> <offsets from start-time>
"r=" fields specify repeat times for a session. For example, if a
session is active at 10am on Monday and 11am on Tuesday for one hour
each week for three months, then the <start-time> in the
corresponding "t=" field would be the NTP representation of 10am on
the first Monday, the <repeat interval> would be 1 week, the <active
duration> would be 1 hour, and the offsets would be zero and 25
hours. The corresponding "t=" field stop time would be the NTP
representation of the end of the last session three months later. By
default all fields are in seconds, so the "r=" and "t=" fields might
be:
t=3034423619 3042462419
r=604800 3600 0 90000
To make description more compact, times may also be given in units of
days, hours or minutes. The syntax for these is a number immediately
Handley, et al. Expires December 10, 2004 [Page 16]
Internet-Draft SDP June 2004
followed by a single case-sensitive character. Fractional units are
not allowed - a smaller unit should be used instead. The following
unit specification characters are allowed:
d - days (86400 seconds)
h - hours (3600 seconds)
m - minutes (60 seconds)
s - seconds (allowed for completeness but not recommended)
Thus, the above session announcement could also have been written:
r=7d 1h 0 25h
Monthly and yearly repeats cannot be directly specified with a single
SDP repeat time - instead separate "t=" fields should be used to
explicitly list the session times.
5.11 Time Zones ("z=")
z=<adjustment time> <offset> <adjustment time> <offset> ....
To schedule a repeated session which spans a change from daylight-
saving time to standard time or vice-versa, it is necessary to
specify offsets from the base time. This is required because
different time zones change time at different times of day, different
countries change to or from daylight time on different dates, and
some countries do not have daylight saving time at all.
Thus in order to schedule a session that is at the same time winter
and summer, it must be possible to specify unambiguously by whose
time zone a session is scheduled. To simplify this task for
receivers, we allow the sender to specify the NTP time that a time
zone adjustment happens and the offset from the time when the session
was first scheduled. The "z=" field allows the sender to specify a
list of these adjustment times and offsets from the base time.
An example might be:
z=2882844526 -1h 2898848070 0
This specifies that at time 2882844526 the time base by which the
session's repeat times are calculated is shifted back by 1 hour, and
that at time 2898848070 the session's original time base is restored.
Adjustments are always relative to the specified start time - they
are not cumulative. Adjustments apply to all "t=" and "r=" lines in
a session description.
If a session is likely to last several years, it is expected that the
Handley, et al. Expires December 10, 2004 [Page 17]
Internet-Draft SDP June 2004
session announcement will be modified periodically rather than
transmit several years worth of adjustments in one session
announcement.
5.12 Encryption Keys ("k=")
k=<method>
k=<method>:<encryption key>
If transported over a secure and trusted channel, the session
description protocol MAY be used to convey encryption keys. A simple
mechanism for key exchange is provided by the key field ("k=")
although this is primarily supported for compatibility with older
implementations and its use is NOT RECOMMENDED. Work is in progress
to define new key exchange mechanisms for use with SDP [18][17] and
it is expected that new applications will use those mechanisms.
A key field is permitted before the first media entry (in which case
it applies to all media in the session), or for each media entry as
required. The format of keys and their usage is outside the scope of
this document, and the key field provides no way to indicate the
encryption algorithm to be used, key type, or other information about
the key: this is assumed to be provided by the higher-level protocol
using SDP. If there is a need to convey this information within SDP,
the extensions mentioned previously SHOULD be used. Many security
protocols require two keys, one for confidentiality and another for
integrity. This specification does not support the transfer of two
keys.
The method indicates the mechanism to be used to obtain a usable key
by external means, or from the encoded encryption key given. The
following methods are defined:
Handley, et al. Expires December 10, 2004 [Page 18]
Internet-Draft SDP June 2004
k=clear:<encryption key>
The encryption key is included untransformed in this key field.
This method MUST NOT be used unless it can be guaranteed that
the SDP is conveyed over a secure channel.
k=base64:<encoded encryption key>
The encryption key is included in this key field but has been
base64 encoded because it includes characters that are
prohibited in SDP. This method MUST NOT be used unless it can
be guaranteed that the SDP is conveyed over a secure channel.
k=uri:<URI to obtain key>
A Universal Resource Identifier is included in the key field.
The URI refers to the data containing the key, and may require
additional authentication before the key can be returned. When
a request is made to the given URI, the reply should specify
the encoding for the key. The URI is often a secure HTTP URI,
although this is not required.
k=prompt
No key is included in this SDP description, but the session or
media stream referred to by this key field is encrypted. The
user should be prompted for the key when attempting to join the
session, and this user-supplied key should then be used to
decrypt the media streams. The use of user-specified keys is
NOT RECOMMENDED, since such keys tend to have weak security
properties.
The key field MUST NOT be used unless it can be guaranteed that the
SDP is conveyed over a secure and trusted channel. An example of such
a channel might be SDP embedded inside an S/MIME message or a TLS
protected HTTP or SIP session. It is important to ensure that the
secure channel is with the party that is authorized to join the
session, not an intermediary: if a caching proxy server is used, it
is important to ensure that the proxy is either trusted or unable to
access the SDP. Definition of appropriate security measures is beyond
the scope of this specification, and should be defined by the users
of SDP.
5.13 Attributes ("a=")
a=<attribute>
a=<attribute>:<value>
Handley, et al. Expires December 10, 2004 [Page 19]
Internet-Draft SDP June 2004
Attributes are the primary means for extending SDP. Attributes may
be defined to be used as "session-level" attributes, "media-level"
attributes, or both.
A media description may have any number of attributes ("a=" fields)
which are media specific. These are referred to as "media-level"
attributes and add information about the media stream. Attribute
fields can also be added before the first media field; these
"session-level" attributes convey additional information that applies
to the conference as a whole rather than to individual media; an
example might be the conference's floor control policy.
Attribute fields may be of two forms:
o property attributes:
A property attribute is simply of the form "a=<flag>".
These are binary attributes, and the presence of the
attribute conveys that the attribute is a property of
the session. An example might be "a=recvonly".
o value attributes:
A value attribute is of the form "a=<attribute>:<value>".
For example, a whiteboard could have the value attribute
"a=orient:landscape"
Attribute interpretation depends on the media tool being invoked.
Thus receivers of session descriptions should be configurable in
their interpretation of session descriptions in general and of
attributes in particular.
Attribute names MUST be in the US-ASCII subset of ISO-10646/UTF-8.
Attribute values are octet strings, and MAY use any octet value
except 0x00 (Nul), 0x0A (LF), and 0x0D (CR). By default, attribute
values are to be interpreted as in ISO-10646 character set with UTF-8
encoding. Unlike other text fields, attribute values are NOT
normally affected by the "charset" attribute as this would make
comparisons against known values problematic. However, when an
attribute is defined, it can be defined to be charset-dependent, in
which case it's value should be interpreted in the session charset
rather than in ISO-10646.
Attributes MUST be registered with IANA (see Section 9). If an
attribute is received that is not understood, it MUST be ignored by
the receiver.
Handley, et al. Expires December 10, 2004 [Page 20]
Internet-Draft SDP June 2004
5.14 Media Descriptions ("m=")
m=<media> <port> <proto> <fmt>
A session description may contain a number of media descriptions.
Each media description starts with an "m=" field, and is terminated
by either the next "m=" field or by the end of the session
description. A media field has several sub-fields.
The first sub-field ("<media>") is the media type. Currently defined
media are "audio", "video", "text", "application", "data" and
"control", though this list may be extended in future (see Section
9). The difference between "application" and "data" is that the
former is a media flow such as whiteboard information, and the latter
is bulk-data transfer such as multicasting of program executables
which will not typically be displayed to the user. "control" is used
to specify an additional conference control channel for the session.
The second sub-field ("<port>") is the transport port to which the
media stream is sent. The meaning of the transport port depends on
the network being used as specified in the relevant "c=" field, and
on the transport protocol defined in the third sub-field. Other
ports used by the media application (such as the RTCP port [12]) MAY
be derived algorithmically from the base media port or MAY be
specified in a separate attribute (e.g. "a=rtcp:" as defined in
[14]).
For applications where hierarchically encoded streams are being sent
to a unicast address, it may be necessary to specify multiple
transport ports. This is done using a similar notation to that used
for IP multicast addresses in the "c=" field:
m=<media> <port>/<number of ports> <transport> <fmt list>
In such a case, the ports used depend on the transport protocol. For
RTP, the default is that only the even numbered ports are used for
data with the corresponding one-higher odd ports used for the RTCP
belonging to the RTP session, and the <number of ports> denoting the
number of RTP sessions. For example:
m=video 49170/2 RTP/AVP 31
would specify that ports 49170 and 49171 form one RTP/RTCP pair and
49172 and 49173 form the second RTP/RTCP pair. RTP/AVP is the
transport protocol and 31 is the format (see below). If non-
contiguous ports are required, they must be signalled using a
separate attribute (e.g. "a=rtcp:" as defined in [14]).
Handley, et al. Expires December 10, 2004 [Page 21]
Internet-Draft SDP June 2004
If multiple addresses are specified in the "c=" field and multiple
ports are specified in the "m=" field, a one-to-one mapping from port
to the corresponding address is implied. For example:
c=IN IP4 224.2.1.1/127/2
m=video 49170/2 RTP/AVP 31
would imply that address 224.2.1.1 is used with ports 49170 and
49171, and address 224.2.1.2 is used with ports 49172 and 49173.
The third sub-field ("<proto>") is the transport protocol. The
transport protocol values are dependent on the address type field in
the "c=" fields. Thus a "c=" field of IP4 defines that the transport
protocol runs over IP4. For IP4, it is normally expected that most
media traffic will be carried as RTP over UDP. The following
transport protocols are defined, but may be extended through
registration of new protocols with IANA (see Section 9):
RTP/AVP - the IETF's Realtime Transport Protocol using the
Audio/Video profile carried over UDP.
udp - User Datagram Protocol
If an application uses a single combined proprietary media format and
transport protocol over UDP, then simply specifying the transport
protocol as udp and using the format field to distinguish the
combined protocol is recommended. If a transport protocol is used
over UDP to carry several distinct media types that need to be
distinguished by a session directory, then specifying the transport
protocol and media format separately is necessary. RTP is an example
of a transport-protocol that carries multiple payload formats that
must be distinguished by the session directory for it to know how to
start appropriate tools, relays, mixers or recorders.
The main reason to specify the transport-protocol in addition to the
media format is that the same standard media formats may be carried
over different transport protocols even when the network protocol is
the same - a historical example is vat PCM audio and RTP PCM audio.
In addition, relays and monitoring tools that are
transport-protocol-specific but format-independent are possible.
For RTP media streams operating under the RTP Audio/Video Profile
[13], the protocol field is "RTP/AVP". Should other RTP profiles be
defined in the future, their profiles will be specified in the same
way. For example, the protocol field "RTP/XYZ" would specify RTP
operating under a profile whose short name is "XYZ".
The fourth and subsequent sub-fields ("<fmt>") are media formats.
For audio, text and video, these SHOULD reference a MIME sub-type
Handley, et al. Expires December 10, 2004 [Page 22]
Internet-Draft SDP June 2004
describing the format under the "audio", "text" and "video" top-level
MIME types.
When a list of payload formats is given, this implies that all of
these formats may be used in the session, but the first of these
formats SHOULD be used as the default format for the session.
For media whose transport protocol is not RTP or UDP the format field
is protocol specific. Such formats should be defined in an
additional specification document.
For media whose transport protocol is RTP, SDP can be used to provide
a dynamic binding of media encoding to RTP payload type. The encoding
names in the RTP AV Profile do not specify unique audio encodings (in
terms of clock rate and number of audio channels), and so they are
not used directly in SDP format fields. Instead, the payload type
number should be used to specify the format for static payload types
and the payload type number along with additional encoding
information should be used for dynamically allocated payload types.
An example of a static payload type is u-law PCM coded single channel
audio sampled at 8kHz. This is completely defined in the RTP Audio/
Video profile as payload type 0, so the media field for such a stream
sent to UDP port 49232 is:
m=audio 49232 RTP/AVP 0
An example of a dynamic payload type is 16 bit linear encoded stereo
audio sampled at 16 kHz. If we wish to use dynamic RTP/AVP payload
type 98 for such a stream, additional information is required to
decode it:
m=audio 49232 RTP/AVP 98
a=rtpmap:98 L16/16000/2
The general form of an rtpmap attribute is:
a=rtpmap:<payload type> <encoding name>/<clock rate>
[/<encoding parameters>]
For audio streams, <encoding parameters> may specify the number of
audio channels. This parameter may be omitted if the number of
channels is one provided no additional parameters are needed.
For video streams, no encoding parameters are currently specified.
Additional parameters may be defined in the future, but codec-
specific parameters SHOULD NOT be added. Parameters added to an
Handley, et al. Expires December 10, 2004 [Page 23]
Internet-Draft SDP June 2004
rtpmap attribute SHOULD only be those required for a session
directory to make the choice of appropriate media to participate in a
session. Codec-specific parameters should be added in other
attributes (for example, "a=fmtp:").
Up to one rtpmap attribute can be defined for each media format
specified. Thus we might have:
m=audio 49230 RTP/AVP 96 97 98
a=rtpmap:96 L8/8000
a=rtpmap:97 L16/8000
a=rtpmap:98 L16/11025/2
RTP profiles that specify the use of dynamic payload types MUST
define the set of valid encoding names and/or a means to register
encoding names if that profile is to be used with SDP.
Note that RTP audio formats typically do not include information
about the number of samples per packet. If a non-default (as defined
in the RTP Audio/Video Profile) packetisation is required, the
"ptime" attribute is used as given below.
For more details on RTP audio and video formats, see [13].
Predefined application formats for the UDP protocol with non-RTP
media are as below:
wb: LBL Whiteboard (transport: udp)
nt: UCL Network Text Editor (transport: udp)
6. Suggested Attributes
The following attributes are defined. Since application writers may
add new attributes as they are required, this list is not exhaustive.
a=cat:<category>
This attribute gives the dot-separated hierarchical category
of the session. This is to enable a receiver to filter
unwanted sessions by category. It is a session-level
attribute, and is not dependent on charset.
a=keywds:<keywords>
Like the cat attribute, this is to assist identifying wanted
sessions at the receiver. This allows a receiver to select
interesting session based on keywords describing the purpose
Handley, et al. Expires December 10, 2004 [Page 24]
Internet-Draft SDP June 2004
of the session. It is a session-level attribute. It is a
charset dependent attribute, meaning that its value should be
interpreted in the charset specified for the session
description if one is specified, or by default in ISO
10646/UTF-8.
a=tool:<name and version of tool>
This gives the name and version number of the tool used to
create the session description. It is a session-level
attribute, and is not dependent on charset.
a=ptime:<packet time>
This gives the length of time in milliseconds represented by
the media in a packet. This is probably only meaningful for
audio data, but may be used with other media types if it makes
sense. It should not be necessary to know ptime to decode RTP
or vat audio, and it is intended as a recommendation for the
encoding/packetisation of audio. It is a media attribute, and
is not dependent on charset.
a=maxptime:<maximum packet time>
The maximum amount of media which can be encapsulated in each
packet, expressed as time in milliseconds. The time SHALL be
calculated as the sum of the time the media present in the
packet represents. The time SHOULD be a multiple of the frame
size. This attribute is probably only meaningful for audio
data, but may be used with other media types if it makes
sense. It is a media attribute, and is not dependent on
charset. Note that this attribute was introduced after RFC
2327, and non updated implementations will ignore this
attribute.
a=rtpmap:<payload type> <encoding name>/<clock rate>
[/<encoding parameters>]
See Section 5.14. This is a media level attribute that is not
dependent on charset.
a=recvonly
This specifies that the tools should be started in receive
only mode where applicable. It can be either a session or
media attribute, and is not dependent on charset. Note that
recvonly applies to the media only, not to any associated
control protocol (e.g. an RTP based system in recvonly mode
Handley, et al. Expires December 10, 2004 [Page 25]
Internet-Draft SDP June 2004
SHOULD still send RTCP packets).
a=sendrecv
This specifies that the tools should be started in send and
receive mode. This is necessary for interactive conferences
with tools that default to receive only mode. It can be either
a session or media attribute, and is not dependent on charset.
If none of the attributes "sendonly", "recvonly", "inactive",
and "sendrecv" is present, "sendrecv" SHOULD be assumed as the
default for sessions which are not of the conference type
"broadcast" or "H332" (see below).
a=sendonly
This specifies that the tools should be started in send-only
mode. An example may be where a different unicast address is
to be used for a traffic destination than for a traffic
source. In such a case, two media descriptions may be use,
one sendonly and one recvonly. It can be either a session or
media attribute, but would normally only be used as a media
attribute, and is not dependent on charset. Note that sendonly
applies only to the media, and any associated control protocol
(e.g. RTCP) SHOULD still be received and processed as normal.
a=inactive
This specifies that the tools should be started in inactive
mode. This is necessary for interactive conferences where
users can put other users on hold. No media is sent over an
inactive media stream. Note that an RTP based system SHOULD
still send RTCP, even if started inactive. It can be either a
session or media attribute, and is not dependent on charset.
a=orient:<whiteboard orientation>
Normally this is only used in a whiteboard media specification.
It specifies the orientation of a the whiteboard on the screen.
It is a media attribute. Permitted values are "portrait",
"landscape" and "seascape" (upside down landscape). It is not
dependent on charset.
a=type:<conference type>
This specifies the type of the conference. Suggested values
are "broadcast", "meeting", "moderated", "test" and "H332".
"recvonly" should be the default for "type:broadcast"
Handley, et al. Expires December 10, 2004 [Page 26]
Internet-Draft SDP June 2004
sessions, "type:meeting" should imply "sendrecv" and
"type:moderated" should indicate the use of a floor control
tool and that the media tools are started so as to mute new
sites joining the conference.
Specifying the attribute "type:H332" indicates that this
loosely coupled session is part of a H.332 session as defined
in the ITU H.332 specification [15]. Media tools should be
started "recvonly".
Specifying the attribute "type:test" is suggested as a hint
that, unless explicitly requested otherwise, receivers can
safely avoid displaying this session description to users.
The type attribute is a session-level attribute, and is not
dependent on charset.
a=charset:<character set>
This specifies the character set to be used to display the
session name and information data. By default, the ISO-10646
character set in UTF-8 encoding is used. If a more compact
representation is required, other character sets may be used.
For example, the ISO 8859-1 is specified with the following
SDP attribute:
a=charset:ISO-8859-1
This is a session-level attribute and is not dependent on
charset. The charset specified MUST be one of those registered
with IANA, such as ISO-8859-1. The character set identifier is
a US-ASCII string and MUST be compared against the IANA
identifiers using a case insensitive comparison. If the
identifier is not recognised or not supported, all strings that
are affected by it SHOULD be regarded as octet strings.
Note that a character set specified MUST still prohibit the
use of bytes 0x00 (Nul), 0x0A (LF) and 0x0d (CR). Character
sets requiring the use of these characters MUST define a
quoting mechanism that prevents these bytes appearing within
text fields.
a=sdplang:<language tag>
This can be a session level attribute or a media level
attribute. As a session level attribute, it specifies the
language for the session description. As a media level
attribute, it specifies the language for any media-level SDP
Handley, et al. Expires December 10, 2004 [Page 27]
Internet-Draft SDP June 2004
information field associated with that media. Multiple
sdplang attributes can be provided either at session or media
level if multiple languages in the session description or
media use multiple languages, in which case the order of the
attributes indicates the order of importance of the various
languages in the session or media from most important to least
important.
In general, sending session descriptions consisting of
multiple languages is discouraged. Instead, multiple
descriptions SHOULD be sent describing the session, one in
each language. However this is not possible with all
transport mechanisms, and so multiple sdplang attributes are
allowed although NOT RECOMMENDED.
The "sdplang" attribute value must be a single RFC 3066
language tag in US-ASCII [6]. It is not dependent on
the charset attribute. An "sdplang" attribute SHOULD be
specified when a session is of sufficient scope to cross
geographic boundaries where the language of recipients cannot
be assumed, or where the session is in a different language
from the locally assumed norm.
a=lang:<language tag>
This can be a session level attribute or a media level
attribute. As a session level attribute, it specifies the
default language for the session being described. As a media
level attribute, it specifies the language for that media,
overriding any session-level language specified. Multiple
lang attributes can be provided either at session or media
level if the session description or media use multiple
languages, in which case the order of the attributes indicates
the order of importance of the various languages in the
session or media from most important to least important.
The "lang" attribute value must be a single RFC 3066 language
tag in US-ASCII [6]. It is not dependent on the charset
attribute. A "lang" attribute SHOULD be specified when a
session is of sufficient scope to cross geographic boundaries
where the language of recipients cannot be assumed, or where
the session is in a different language from the locally
assumed norm.
a=framerate:<frame rate>
This gives the maximum video frame rate in frames/sec. It is
intended as a recommendation for the encoding of video data.
Handley, et al. Expires December 10, 2004 [Page 28]
Internet-Draft SDP June 2004
Decimal representations of fractional values using the
notation "<integer>.<fraction>" are allowed. It is a
media attribute, defined only for video media, and is not
dependent on charset.
a=quality:<quality>
This gives a suggestion for the quality of the encoding as an
integer value. The intention of the quality attribute for
video is to specify a non-default trade-off between frame-rate
and still-image quality. For video, the value in the range 0
to 10, with the following suggested meaning:
10 - the best still-image quality the compression scheme
can give.
5 - the default behaviour given no quality suggestion.
0 - the worst still-image quality the codec designer
thinks is still usable.
It is a media attribute, and is not dependent on charset.
a=fmtp:<format> <format specific parameters>
This attribute allows parameters that are specific to a
particular format to be conveyed in a way that SDP doesn't
have to understand them. The format must be one of the
formats specified for the media. Format-specific parameters
may be any set of parameters required to be conveyed by SDP
and given unchanged to the media tool that will use this
format. At most one instance of this attribute is allowed
for each format.
It is a media attribute, and is not dependent on charset.
7. Communicating Conference Control Policy
There is some debate over the way conference control policy should be
communicated. In general, the authors believe that an implicit
declarative style of specifying conference control is desirable where
possible.
A simple declarative style uses a single conference attribute field
before the first media field, possibly supplemented by properties
such as `recvonly' for some of the media tools. This conference
attribute conveys the conference control policy. An example might
be:
Handley, et al. Expires December 10, 2004 [Page 29]
Internet-Draft SDP June 2004
a=type:moderated
In some cases, however, it is possible that this may be insufficient
to communicate the details of an unusual conference control policy.
If this is the case, then a conference attribute specifying external
control might be set, and then one or more "media" fields might be
used to specify the conference control tools and configuration data
for those tools. An example is an ITU H.332 session:
...
c=IN IP4 224.5.6.7
a=type:H332
m=audio 49230 RTP/AVP 0
m=video 49232 RTP/AVP 31
m=application 12349 udp wb
m=control 49234 H323 mc
c=IN IP4 134.134.157.81
In this example, a general conference attribute (type:H332) is
specified stating that conference control will be provided by an
external H.332 tool, and a contact addresses for the H.323 session
multipoint controller is given.
In this document, only the declarative style of conference control
declaration is specified. Other forms of conference control should
specify an appropriate type attribute, and should define the
implications this has for control media.
8. Security Considerations
SDP is a session description format that describes multimedia
sessions. A session description SHOULD NOT be trusted unless it has
been obtained by an authenticated transport protocol from a trusted
source. Many different transport protocols may be used to distribute
session description, and the nature of the authentication will differ
from transport to transport.
One transport that will frequently be used to distribute session
descriptions is the Session Announcement Protocol (SAP). SAP
provides both encryption and authentication mechanisms but due to the
nature of session announcements it is likely that there are many
occasions where the originator of a session announcement cannot be
authenticated because they are previously unknown to the receiver of
the announcement and because no common public key infrastructure is
available.
On receiving a session description over an unauthenticated transport
mechanism or from an untrusted party, software parsing the session
Handley, et al. Expires December 10, 2004 [Page 30]
Internet-Draft SDP June 2004
should take a few precautions. Session descriptions contain
information required to start software on the receivers system.
Software that parses a session description MUST NOT be able to start
other software except that which is specifically configured as
appropriate software to participate in multimedia sessions. It is
normally considered inappropriate for software parsing a session
description to start, on a user's system, software that is
appropriate to participate in multimedia sessions, without the user
first being informed that such software will be started and giving
their consent. Thus a session description arriving by session
announcement, email, session invitation, or WWW page MUST NOT deliver
the user into an interactive multimedia session unless the user has
explicitly pre-authorized such action. As it is not always simple to
tell whether a session is interactive or not, applications that are
unsure should assume sessions are interactive.
In this specification, there are no attributes which would allow the
recipient of a session description to be informed to start multimedia
tools in a mode where they default to transmitting. Under some
circumstances it might be appropriate to define such attributes. If
this is done an application parsing a session description containing
such attributes SHOULD either ignore them, or inform the user that
joining this session will result in the automatic transmission of
multimedia data. The default behaviour for an unknown attribute is
to ignore it.
Session descriptions may be parsed at intermediate systems such as
firewalls for the purposes of opening a hole in the firewall to allow
the participation in multimedia sessions. It is considered
inappropriate for a firewall to open such holes for unicast data
streams unless the session description comes in a request from inside
the firewall. For multicast sessions, it is likely that local
administrators will apply their own policies, but the exclusive use
of "local" or "site-local" administrative scope within the firewall
and the refusal of the firewall to open a hole for such scopes will
provide separation of global multicast sessions from local ones.
Use of the "k=" field poses a significant security risk, since it
conveys session encryption keys in the clear. SDP MUST NOT be used
to convey key material, unless it can be guaranteed that the channel
over which the SDP is delivered is both private and authenticated.
9. IANA Considerations
9.1 The "application/sdp" media type
One MIME type is to be registered, as defined below. This updates the
previous definition from RFC 2327.
Handley, et al. Expires December 10, 2004 [Page 31]
Internet-Draft SDP June 2004
To: ietf-types@iana.org
Subject: Registration of MIME media type application/sdp
MIME media type name: application
MIME subtype name: sdp
Required parameters: None.
Optional parameters: None.
Encoding considerations:
See section 5 of RFC XXXX
Security considerations:
See section 8 of RFC XXXX
Interoperability considerations:
See RFC XXXX
Published specification:
RFC XXXX
Applications which use this media type:
Voice over IP, video teleconferencing, streaming media, instant
messaging, etc. See also section 3 of RFC XXXX.
Additional information:
Magic number(s): None.
File extension(s): The extension ".sdp" is commonly used.
Macintosh File Type Code(s): "sdp "
Person & email address to contact for further information:
Colin Perkins <csp@csperkins.org>
IETF MMUSIC working group
Intended usage: COMMON
Author/Change controller:
Authors of RFC XXXX
IETF MMUSIC working group
9.2 Registration of Parameters
There are seven field names that may be registered with IANA. Using
Handley, et al. Expires December 10, 2004 [Page 32]
Internet-Draft SDP June 2004
the terminology in the SDP specification BNF, they are "media",
"proto", "fmt", "att-field", "bwtype", "nettype" and "addrtype".
9.2.1 Media types ("media")
The set of media types is intended to be small and SHOULD NOT be
extended except under rare circumstances. The same rules should
apply for media names as for top-level MIME content types, and where
possible the same name should be registered for SDP as for MIME. For
media other than existing MIME top-level content types, a
standards-track RFC MUST be produced for a new top-level content type
to be registered, and the registration MUST provide good
justification why no existing media name is appropriate (the
"Standards Action" policy of RFC 2434 [5].
This memo registers the media types "audio", "video", "text",
"application", "data" and "control".
9.2.2 Transport protocols ("proto")
The "proto" field describes the transport protocol used. This SHOULD
reference a standards-track protocol RFC. This memo registers three
values: "RTP/AVP" is a reference to RTP [12] used under the RTP
Profile for Audio and Video Conferences with Minimal Control [13]
running over UDP/IP, "RTP/SAVP" is a reference to the Secure
Real-time Transport Protocol [15], and "udp" indicates an unspecified
format over UDP.
New transport protocols MAY be registered with IANA. Registrations
MUST reference an RFC describing the protocol. Such an RFC MAY be
Experimental or Informational, although it is preferable if it is
Standards-Track. Registrations MUST also define the rules by which
their "fmt" namespace is managed (see below).
9.2.3 Media formats ("fmt")
Each transport protocol, defined by the "proto" field, has an
associated "fmt" namespace that describes the media formats which may
conveyed by that protocol. Formats cover all the possible encodings
that might want to be transported in a multimedia session.
RTP payload formats under the "RTP/AVP" and "RTP/SAVP" profiles MUST
use the payload type number as their "fmt" value. If the payload
type number is dynamically assigned by this session description, an
additional "rtpmap" attribute MUST be included to specify the format
name and parameters as defined by the MIME type registration for the
payload format. It is RECOMMENDED that other RTP profiles which are
registered (in combination with RTP) as SDP transport protocols
Handley, et al. Expires December 10, 2004 [Page 33]
Internet-Draft SDP June 2004
specify the same rules for the "fmt" namespace.
For the "udp" protocol, new formats SHOULD be registered. Use of an
existing MIME subtype for the format is encouraged. If no MIME
subtype exists, it is RECOMMENDED that a suitable one is registered
through the IETF process (RFC 2048) by production of, or reference
to, a standards-track RFC. If a MIME subtype is for some reason
inappropriate, an RFC publication describing the format MUST be
referenced in the registration, but it may be Informational or
Experimental if the protocol is not deemed to be of widespread
deployment.
For other protocols, formats MAY be registered according to the rules
of the associated "proto" specification.
Registrations of new formats MUST specify which transport protocols
they apply to.
9.2.4 Attribute names ("att-field")
Attribute field names ("att-field") MUST be registered with IANA and
documented, because of noticeable issues due to conflicting
attributes under the same name. Unknown attributes in SDP are simply
ignored, but conflicting ones that fragment the protocol are a
serious problem.
New attribute registerations are accepted according to the
"Specification Required" policy of RFC 2434, provided that the
specification includes the following information:
o contact name, email address and telephone number
o attribute-name (as it will appear in SDP)
o long-form attribute name in English
o type of attribute (session level, media level, or both)
o whether the attribute value is subject to the charset attribute.
o a one paragraph explanation of the purpose of the attribute.
o a specification of appropriate attribute values for this
attribute.
The above is the minimum that IANA will accept. Attributes that are
expected to see widespread use and interoperability, SHOULD be
documented with a standards-track RFC that specifies the attribute
more precisely.
Submitters of registrations should ensure that the specification is
in the spirit of SDP attributes, most notably that the attribute is
platform independent in the sense that it makes no implicit
assumptions about operating systems and does not name specific pieces
of software in a manner that might inhibit interoperability.
Handley, et al. Expires December 10, 2004 [Page 34]
Internet-Draft SDP June 2004
IANA is requested to register the following initial set of attribute
names ("att-field" values), with definitions as in Section 6 of this
memo (these definitions update those in RFC 2327):
Name | Session or Media level? | Dependent on charset?
----------+-------------------------+----------------------
cat | Session | No
keywds | Session | Yes
tool | Session | No
ptime | Media | No
maxptime | Media | No
rtpmap | Media | No
recvonly | Either | No
sendrecv | Either | No
sendonly | Either | No
inactive | Either | No
orient | Media | No
type | Session | No
charset | Session | No
sdplang | Either | No
lang | Either | No
framerate | Media | No
quality | Media | No
fmtp | Media | No
9.2.5 Bandwidth specifiers ("bwtype")
A proliferation of bandwidth specifiers is strongly discouraged.
New bandwidth specifiers ("bwtype" fields) MUST be registered with
IANA. The submission MUST reference a standards-track RFC specifying
the semantics of the bandwidth specifier precisely, and indicating
when it should be used, and why the existing registered bandwidth
specifiers do not suffice.
IANA is requested to register the bandwith specifiers "CT" and "AS"
with definitions as in Section 5.8 of this memo (these definitions
update those in RFC 2327).
9.2.6 Network types ("nettype")
New network types (the "nettype" field) may be registered with IANA
if SDP needs to be used in the context of non-Internet environments.
Whilst these are not normally the preserve of IANA, there may be
circumstances when an Internet application needs to interoperate with
a non- Internet application, such as when gatewaying an Internet
telephony call into the PSTN. The number of network types should be
Handley, et al. Expires December 10, 2004 [Page 35]
Internet-Draft SDP June 2004
small and should be rarely extended. A new network type cannot be
registered without registering at least one address type to be used
with that network type. A new network type registration MUST
reference an RFC which gives details of the network type and address
type and specifies how and when they would be used. Such an RFC MAY
be Informational.
IANA is requested to register the network type "IN" to represent the
Internet, with definition as in Sections 5.2 and 5.7 of this memo
(these definitions update those in RFC 2327).
9.2.7 Address types ("addrtype")
New address types ("addrtype") may be registered with IANA. An
address type is only meaningful in the context of a network type, and
any registration of an address type MUST specify a registered network
type, or be submitted along with a network type registration. A new
address type registration MUST reference an RFC giving details of the
syntax of the address type. Such an RFC MAY be Informational.
Address types are not expected to be registered frequently.
IANA is requested to register the address types "IP4" and "IP6" with
definitions as in Sections 5.2 and 5.7 of this memo (these
definitions update those in RFC 2327).
9.2.8 Registration Procedure
In the RFC documentation that registers SDP "media", "proto", "fmt",
"bwtype", "nettype" and "addrtype" fields, the authors MUST include
the following information for IANA to place in the appropriate
registry:
o contact name, email address and telephone number
o name being registered (as it will appear in SDP)
o long-form name in English
o type of name ("media", "proto", "fmt", "bwtype", "nettype", or
"addrtype")
o a one paragraph explanation of the purpose of the registered name.
o a reference to the specification (e.g. RFC number) of the
registered name.
IANA may refer any registration to the IESG Transport Area Directors
for review, and may request revisions to be made before a
registration will be made.
9.3 Encryption Key Access Methods
The IANA currently maintains a table of SDP encryption key access
method ("enckey") names. This table is obsolete and SHOULD be
Handley, et al. Expires December 10, 2004 [Page 36]
Internet-Draft SDP June 2004
removed, since the "k=" line is not extensible. New registrations
MUST NOT be accepted.
Appendix A. SDP Grammar
This appendix provides an Augmented BNF grammar for SDP. ABNF is
defined in [2].
; SDP Syntax
session-description = proto-version
origin-field
session-name-field
information-field
uri-field
email-fields
phone-fields
connection-field
bandwidth-fields
time-fields
key-field
attribute-fields
media-descriptions
proto-version = "v=" 1*DIGIT CRLF
;this memo describes version 0
origin-field = "o=" username SP sess-id SP sess-version SP
nettype SP addrtype SP unicast-address CRLF
session-name-field = "s=" text CRLF
information-field = ["i=" text CRLF]
uri-field = ["u=" uri CRLF]
email-fields = *("e=" email-address CRLF)
phone-fields = *("p=" phone-number CRLF)
connection-field = ["c=" nettype SP addrtype SP
connection-address CRLF]
;a connection field must be present
;in every media description or at the
;session-level
bandwidth-fields = *("b=" bwtype ":" bandwidth CRLF)
time-fields = 1*( "t=" start-time SP stop-time
Handley, et al. Expires December 10, 2004 [Page 37]
Internet-Draft SDP June 2004
*(CRLF repeat-fields) CRLF)
[zone-adjustments CRLF]
repeat-fields = "r=" repeat-interval SP typed-time
1*(SP typed-time)
zone-adjustments = "z=" time SP ["-"] typed-time
*(SP time SP ["-"] typed-time)
key-field = ["k=" key-type CRLF]
attribute-fields = *("a=" attribute CRLF)
media-descriptions = *( media-field
information-field
*connection-field
bandwidth-fields
key-field
attribute-fields )
media-field = "m=" media SP port ["/" integer]
SP proto 1*(SP fmt) CRLF
; sub-rules of 'o='
username = non-ws-string
;pretty wide definition, but doesn't
;include space
sess-id = 1*DIGIT
;should be unique for this username/host
sess-version = 1*DIGIT
;0 is a new session
nettype = token
;typically "IN"
addrtype = token
;typically "IP4" or "IP6"
; sub-rules of 'u='
uri = URI-reference; see RFC1630 and RFC2732
; sub-rules of 'e='
email-address = email *SP "(" 1*email-safe ")" /
1*email-safe "<" email ">" /
email
Handley, et al. Expires December 10, 2004 [Page 38]
Internet-Draft SDP June 2004
email = addr-spec ; defined in RFC2822
; modified to remove CFWS
; sub-rules of 'p='
phone-number = phone *SP "(" 1*email-safe ")" /
1*email-safe "<" phone ">" /
phone
phone = "+" POS-DIGIT 1*(SP / "-" / DIGIT)
; sub-rules of 'c='
connection-address = multicast-address / unicast-address
; sub-rules of 'b='
bwtype = token
bandwidth = 1*DIGIT
; sub-rules of 't='
start-time = time / "0"
stop-time = time / "0"
time = POS-DIGIT 9*DIGIT
; 10-digit NTP time represents times between
; 1931 and 5068 AD. 9* allows times after
; that as well.
; sub-rules of 'r=' and 'z='
repeat-interval = POS-DIGIT *DIGIT [fixed-len-time-unit]
typed-time = 1*DIGIT [fixed-len-time-unit]
fixed-len-time-unit = "d" / "h" / "m" / "s"
; sub-rules of 'k='
key-type = "prompt" /
"clear:" text /
"base64:" base64 /
"uri:" uri /
key-method [ ":" text ]
base64 = *base64-unit [base64-pad]
base64-unit = 4base64-char
base64-pad = 2base64-char "==" / 3base64-char "="
base64-char = ALPHA / DIGIT / "+" / "/"
key-method = token
Handley, et al. Expires December 10, 2004 [Page 39]
Internet-Draft SDP June 2004
; sub-rules of 'a='
attribute = (att-field ":" att-value) / att-field
att-field = token
att-value = byte-string
; sub-rules of 'm='
media = token
;typically "audio", "video", "text",
;"application" or "data"
fmt = token
;typically an RTP payload type for audio
;and video media
proto = token *("/" token)
;typically "RTP/AVP" or "udp"
port = 1*DIGIT
;should be either "0" or in the range "1024"
;to "65535" inclusive for UDP based media
;(a value of "0" is used to signal special
;conditions in some uses of SDP)
; generic sub-rules: addressing
unicast-address = IP4-address / IP6-address / FQDN / extn-addr
multicast-address = IP4-multicast / IP6-multicast
IP4-multicast = m1 3( "." decimal-uchar )
"/" ttl [ "/" integer ]
; IPv4 multicast addresses may be in the
; range 224.0.0.0 to 239.255.255.255
m1 = ("22" ("4"/"5"/"6"/"7"/"8"/"9")) /
("23" DIGIT )
IP6-multicast = hexpart [ "/" integer ]
; IPv6 address starting with FF
ttl = (POS-DIGIT *2DIGIT) / "0"
FQDN = 4*(alpha-numeric / "-" / ".")
; fully qualified domain name as specified
; in RFC1035
IP4-address = b1 3("." decimal-uchar) / "0.0.0.0"
Handley, et al. Expires December 10, 2004 [Page 40]
Internet-Draft SDP June 2004
b1 = decimal-uchar
; less than "224"; not "0" or "127"
; The following is from RFC2373 Appendix B. It is a direct copy.
IP6-address = hexpart [ ":" IP4-address ]
hexpart = hexseq / hexseq "::" [ hexseq ] /
"::" [ hexseq ]
hexseq = hex4 *( ":" hex4)
hex4 = 1*4HEXDIG
; Generic for other address families
extn-addr = non-ws-string
; generic sub-rules: datatypes
text = byte-string
;default is to interpret this as UTF8 text.
;ISO 8859-1 requires "a=charset:ISO-8859-1"
;session-level attribute to be used
byte-string = 1*(%x01-09/%x0B-0C/%x0E-FF)
;any byte except NUL, CR or LF
non-ws-string = 1*(VCHAR/%x80-FF)
;string of visible characters
token-char = %x21 / %x23-27 / %x2A-2B / %x2D-2E / %x30-39
/ %x41-5A / %x5E-7E
token = 1*(token-char)
email-safe = %x01-09/%x0B-0C/%x0E-27/%x2A-3B/%x3D/%x3F-FF
;any byte except NUL, CR, LF, or the quoting
;characters ()<>
integer = POS-DIGIT *DIGIT
; generic sub-rules: primitives
alpha-numeric = ALPHA / DIGIT
POS-DIGIT = %x31-39 ; 1 - 9
decimal-uchar = DIGIT
/ POS-DIGIT DIGIT
/ ("1" 2*(DIGIT))
/ ("2" ("0"/"1"/"2"/"3"/"4") DIGIT)
Handley, et al. Expires December 10, 2004 [Page 41]
Internet-Draft SDP June 2004
/ ("2" "5" ("0"/"1"/"2"/"3"/"4"/"5"))
; external references:
; ALPHA, DIGIT, CRLF, SP, VCHAR: from RFC 2234
; URI-reference: from RFC1630 and RFC2732
; addr-spec: from RFC 2822
Appendix B. Acknowledgments
Many people in the IETF MMUSIC working group have made comments and
suggestions contributing to this document. In particular, we would
like to thank Eve Schooler, Steve Casner, Bill Fenner, Allison
Mankin, Ross Finlayson, Peter Parnes, Joerg Ott, Carsten Bormann,
Steve Hanna, Jonathan Lennox and Keith Drage.
10. References
10.1 Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Crocker, D. and P. Overell, "Augmented BNF for Syntax
Specifications: ABNF", RFC 2234, November 1997.
[3] Yergeau, F., "UTF-8, a transformation format of ISO 10646", RFC
2279, January 1998.
[4] Berners-Lee, T., Fielding, R. and L. Masinter, "Uniform Resource
Identifiers (URI): Generic Syntax", RFC 2396, August 1998.
[5] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434, October 1998.
[6] Alvestrand, H., "Tags for the Identification of Languages", BCP
47, RFC 3066, January 2001.
10.2 Informative References
[7] Mills, D., "Network Time Protocol (Version 3) Specification,
Implementation", RFC 1305, March 1992.
[8] Handley, M., Perkins, C. and E. Whelan, "Session Announcement
Protocol", RFC 2974, October 2000.
[9] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
Peterson, J., Sparks, R., Handley, M. and E. Schooler, "SIP:
Handley, et al. Expires December 10, 2004 [Page 42]
Internet-Draft SDP June 2004
Session Initiation Protocol", RFC 3261, June 2002.
[10] Schulzrinne, H., Rao, A. and R. Lanphier, "Real Time Streaming
Protocol (RTSP)", RFC 2326, April 1998.
[11] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with
Session Description Protocol (SDP)", RFC 3264, June 2002.
[12] Schulzrinne, H., Casner, S., Frederick, R. and V. Jacobson,
"RTP: A Transport Protocol for Real-Time Applications", RFC
3550, July 2003.
[13] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and Video
Conferences with Minimal Control", RFC 3551, July 2003.
[14] Huitema, C., "Real Time Control Protocol (RTCP) attribute in
Session Description Protocol (SDP)", RFC 3605, October 2003.
[15] Baugher, M., McGrew, D., Naslund, M., Carrara, E. and K.
Norrman, "The Secure Real-time Transport Protocol (SRTP)", RFC
3711, March 2004.
[16] International Telecommunications Union, "H.323 extended for
loosely coupled conferences", ITU Recommendation H.332,
September 1998.
[17] Arkko, J., "Key Management Extensions for Session Description
Protocol (SDP) and Real Time Streaming Protocol (RTSP)",
draft-ietf-mmusic-kmgmt-ext-09 (work in progress), October
2003.
[18] Andreasen, F., Baugher, M. and D. Wing, "SDP Security
Descriptions for Media Streams",
draft-ietf-mmusic-sdescriptions-02 (work in progress), October
2003.
Authors' Addresses
Mark Handley
University College London
Gower Street
London WC1E 6BT
UK
EMail: M.Handley@cs.ucl.ac.uk
Handley, et al. Expires December 10, 2004 [Page 43]
Internet-Draft SDP June 2004
Van Jacobson
Packet Design
2465 Latham Street
Mountain View, CA 94040
USA
EMail: van@packetdesign.com
Colin Perkins
University of Glasgow
17 Lilybank Gardens
Glasgow G12 8QQ
UK
EMail: csp@csperkins.org
Handley, et al. Expires December 10, 2004 [Page 44]
Internet-Draft SDP June 2004
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the IETF's procedures with respect to rights in IETF Documents can
be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2004). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Handley, et al. Expires December 10, 2004 [Page 45]
Html markup produced by rfcmarkup 1.129d, available from
https://tools.ietf.org/tools/rfcmarkup/