draft-ietf-adslmib-adslext-12.txt   rfc3440.txt 
INTERNET-DRAFT ADSL Line Extension MIB Faye Ly Network Working Group F. Ly
Pedestal Networks Request for Comments: 3440 Pedestal Networks
Gregory Bathrick Category: Standards Track G. Bathrick
Nokia Nokia
September 23, 2002 December 2002
Definitions of Extension Managed Objects Definitions of Extension Managed Objects
for Asymmetric Digital Subscriber Lines for Asymmetric Digital Subscriber Lines
September 23, 2002 Status of this Memo
draft-ietf-adslmib-adslext-12.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as ``work in progress.''
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
The list of Internet-Draft Shadow Directories can be accessed at This document specifies an Internet standards track protocol for the
http://www.ietf.org/shadow.html Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved. Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract Abstract
This memo defines a portion of the Management Information Base (MIB) This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community. for use with network management protocols in the Internet community.
In particular, it describes additional managed objects used for In particular, it describes additional managed objects used for
managing Asymmetric Digital Subscriber Line (ADSL) interfaces not managing Asymmetric Digital Subscriber Line (ADSL) interfaces not
covered by the ADSL Line MIB (RFC 2662). covered by the ADSL Line MIB (RFC 2662).
1. The SNMP Network Management Framework Table of Contents
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events
for the purpose of management. The first version of this
Structure of Management Information (SMI) is called SMIv1
and described in STD 16, RFC 1155 [RFC1155], STD 16,
RFC 1212 [RFC1212] and RFC 1215 [RFC1215]. The second version,
called SMIv2, is described in STD 58, RFC 2578 [RFC2578],
STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
o Message protocols for transferring management information.
The first version of the SNMP message protocol is called
SNMPv1 and described in STD 15, RFC 1157[RFC1157]. A second
version of the SNMP message protocol, which is not an Internet
standards track protocol, is called SNMPv2c and described in RFC
1901 [RFC1901] and RFC 1906 [RFC1906]. The third version of the
message protocol is called SNMPv3 and described in RFC 1906
[RFC1906], RFC2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The 1. The Internet-Standard Management Framework ................. 2
first set of protocol operations and associated PDU formats is 2. Introduction ............................................... 2
described in STD 15, RFC 1157 [RFC1157]. A second set of protocol 3. Relationship of ADSL LINE EXTENSION MIB with standard MIBs . 2
operations and associated PDU formats is described in RFC 1905 4. Conventions used in the MIB ................................ 2
[RFC1905]. 5. Conformance and Compliance ................................. 6
6. Definitions ................................................ 6
7. Acknowledgments ............................................31
8. References .................................................31
9. Security Considerations ....................................32
10. Intellectual Property Notice ...............................34
11. Authors' Addresses .........................................35
12. Full Copyright Statement ...................................36
o A set of fundamental applications described in RFC 2573 1. The Internet-Standard Management Framework
[RFC2573] and the view-based access control mechanism described in
RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework For a detailed overview of the documents that describe the current
can be found in RFC 2570 [RFC2570]. Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are the Management Information Base or MIB. MIB objects are generally
defined using the mechanisms defined in the SMI. accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
This memo specifies a MIB module that is compliant to the SMIv2. A Structure of Management Information (SMI). This memo specifies a MIB
MIB conforming to the SMIv1 can be produced through the appropriate module that is compliant to the SMIv2, which is described in STD 58,
translations. The resulting translated MIB must be semantically RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
equivalent, except where objects or events are omitted because no [RFC2580].
translation is possible (use of Counter64). Some machine-readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
2. Introduction 2. Introduction
The purpose of this memo is to define a supplemental set of managed The purpose of this memo is to define a supplemental set of managed
objects that is not covered by ADSL Line MIB as defined in [RFC2662]. objects that is not covered by the ADSL Line MIB as defined in
This memo addresses the additional objects defined in ITU G.997.1 [RFC2662]. This memo addresses the additional objects defined in ITU
[ITU G.997.1]. G.997.1 [ITU G.997.1].
3. Relationship of ADSL Line Extension MIB with standard MIBs 3. Relationship of ADSL Line Extension MIB with standard MIBs
This section outlines the relationship of ADSL Line Extension MIB This section outlines the relationship of the ADSL Line Extension MIB
with other MIBs described in RFCs and in their various degrees with other MIBs described in RFCs and in their various degrees of
of standardization. In regards to these relationship, the ADSL Line standardization. In regards to these relationships, the ADSL Line
Extension MIB follows conventions as used by the ADSL Line MIB with Extension MIB follows conventions as used by the ADSL Line MIB with
one exception. The value of the RFC2863 object, ifOperstatus, one exception. The value of the RFC 2863 object, ifOperstatus, SHALL
SHALL be down(2) when the ADSL line interface is in power state L3 as be down(2) when the ADSL line interface is in power state L3, as
defined in ITU G.992.1 [ITU G.992.1], which means no power. Its value defined in ITU G.992.1 [ITU G.992.1], which means no power. Its
shall be up(1) if the ADSL line interface is in power state L0 (power on) value shall be up(1) if the ADSL line interface is in power state L0
[ITU G.992.1] or L1 (reduced power). Power Status L2 [ITU G.992.1] is (power on) [ITU G.992.1] or L1 (reduced power). Power Status L2 [ITU
not applicable. G.992.1] is not applicable.
4. Conventions used in the MIB 4. Conventions used in the MIB
4.1 Structure 4.1 Structure
The MIB is organized to follow the same structure of the ADSL Line The MIB is organized to follow the same structure of the ADSL Line
MIB [RFC2662]. MIB [RFC2662].
4.2 Additional Managed Objects 4.2 Additional Managed Objects
Objects specific to the management of ADSL G.Lite as defined in Objects specific to the management of ADSL G.Lite as defined in ITU
ITU G.992.2 [ITU G.992.2] are: G.992.2 [ITU G.992.2] are:
- ADSL Transceiver Unit - Central Office End (ATU-C) - ADSL Transceiver Unit - Central Office End (ATU-C)
Transmission System and Line Mode Transmission System and Line Mode
- Power Management - Power Management
- Counters for Fast Retrains and Failed Fast Retrains - Counters for Fast Retrains and Failed Fast Retrains
- Counters for Severe Error Second-line and Unavailable Second - Counters for Severe Error Second-line and Unavailable Second
- Alternative profile configuration for the Dual line mode interface - Alternative profile configuration for the Dual line mode
interface
Besides the management of G.Lite, another object has been added in Besides the management of G.Lite, another object has been added in
order to manage the ADSL line profile. The object is the line mode order to manage the ADSL line profile. The object is the line mode
configuration. configuration.
4.2.1 ATU-C ADSL Transmission System Parameters and Line Mode 4.2.1 ATU-C ADSL Transmission System Parameters and Line Mode
The adslLineConfigTable needs to be extended to cover control of the The adslLineConfigTable needs to be extended to cover control of the
ATU-C ADSL Transmission system. Three objects are defined to monitor ATU-C ADSL Transmission system. Three objects are defined to monitor
and configure the transmission mode as well as the actual line mode: and configure the transmission mode as well as the actual line mode:
- Capability - Capability
- Configuration - Configuration
- Actual Status - Actual Status
Transmission modes can further determine the line mode of the ADSL Transmission modes can further determine the line mode of the ADSL
interface. For example, if g9921PotsNonOverlapped(2) is the actual interface. For example, if g9921PotsNonOverlapped(2) is the actual
value of the ADSL interface, the interface is operating in Full rate value of the ADSL interface, the interface is operating in Full rate
ADSL. If the interface is set to g9922PotsOverlapped(9), the ADSL. If the interface is set to g9922PotsOverlapped(9), the
interface is operating in G.Lite mode. interface is operating in G.Lite mode.
The transmission mode and the corresponding line mode are defined as: The transmission mode and the corresponding line mode are defined as:
Transmission mode Line Mode Transmission mode Line Mode
skipping to change at page 4, line 38 skipping to change at page 4, line 27
G.992.1 ISDN overlapped Full G.992.1 ISDN overlapped Full
G.992.1 TCM-ISDN non-overlapped Full G.992.1 TCM-ISDN non-overlapped Full
G.992.1 TCM-ISDN overlapped Full G.992.1 TCM-ISDN overlapped Full
G.992.2 POTS non-overlapped G.Lite G.992.2 POTS non-overlapped G.Lite
G.992.2 POTS overlapped G.Lite G.992.2 POTS overlapped G.Lite
G.992.2 with TCM-ISDN G.Lite G.992.2 with TCM-ISDN G.Lite
non-overlapped non-overlapped
G.992.2 with TCM-ISDN overlapped G.Lite G.992.2 with TCM-ISDN overlapped G.Lite
G.992.1 TCM-ISDN symmetric Full G.992.1 TCM-ISDN symmetric Full
Table 1: Transmission Mode and Line Mode Table 1: Transmission Mode and Line Mode
In case more than one bit is configured for an ADSL interface and In case more than one bit is configured for an ADSL interface and
both Full and G.Lite modes are selected, the interface is said to both Full and G.Lite modes are selected, the interface is said to be
be configured in the dual mode. Only one bit can be set in the Actual configured in the dual mode. Only one bit can be set in the Actual
object that reflects the actual mode of transmission as well as the object that reflects the actual mode of transmission as well as the
line mode. line mode.
4.2.2 Power Management 4.2.2 Power Management
There are three possible power states for each managed ADSL interface There are three possible power states for each managed ADSL interface
operating in the G.Lite mode. L0 is power on, L1 is power on but operating in the G.Lite mode. L0 is power on, L1 is power on but
reduced and L3 is power off. Power state cannot be configured by an reduced and L3 is power off. Power state cannot be configured by an
operator but it can be viewed via the ifOperStatus object for the operator but it can be viewed via the ifOperStatus object for the
managed ADSL interface. The value of the object ifOperStatus is managed ADSL interface. The value of the object ifOperStatus is set
set to down(2) if the ADSL interface is in power state L3 and is set to down(2) if the ADSL interface is in power state L3 and is set to
to up(1) if the ADSL line interface is in power state L0 or L1. up(1) if the ADSL line interface is in power state L0 or L1.
An ADSL line power state, if the interface is operating in the An ADSL line power state, if the interface is operating in the G.Lite
G.Lite mode, can also be monitored by the adslLineGlitePowerState mode, can also be monitored by the adslLineGlitePowerState object
object defined in the ADSL Line Extension table. The value of the defined in the ADSL Line Extension table. The value of the object
object enumerates the three power states attainable by the managed enumerates the three power states attainable by the managed
interface. interface.
4.2.3 Fast Retrain Parameters 4.2.3 Fast Retrain Parameters
Section 7.4.15 [ITU G.997.1] specifies fast retrain parameters. Fast Section 7.4.15 [ITU G.997.1] specifies fast retrain parameters. Fast
retrain parameters include two counters: fast retrain count and failed retrain parameters include two counters: fast retrain count and
fast retrain count. These two counters have been added to all failed fast retrain count. These two counters have been added to all
performance tables. performance tables.
4.2.4 Counters for Severely Errored Second-line and Unavailable 4.2.4 Counters for Severely Errored Second-line and Unavailable
Seconds-line Seconds-line
ITU G.997.1 sections 6.2.1.1.7 and 6.2.1.1.9 specify two counters that ITU G.997.1 sections 6.2.1.1.7 and 6.2.1.1.9 specify two counters
are not covered by the ADSL Line MIB [RFC2662]. These two counters that are not covered by the ADSL Line MIB [RFC2662]. These two
(severely errored seconds-line and unavailable seconds-line) are added counters (severely errored seconds-line and unavailable seconds-line)
to all the performance tables. are added to all the performance tables.
Unavailable seconds counts cumulative number of seconds in which the Unavailable seconds counts the cumulative number of seconds in which
interface was unavailable during the measured period. This counter the interface was unavailable during the measured period. This
does not include the seconds in which unavailability was caused solely counter does not include the seconds in which unavailability was
by fast retrains and failed fast retrains. Fast retrains and failed caused solely by fast retrains and failed fast retrains. Fast
fast retrains are considered to be part of the normal network operation retrains and failed fast retrains are considered to be part of the
and thus are not counted as unavailable errors. normal network operation and thus are not counted as unavailable
errors.
4.2.5 Counters, Interval Buckets and Thresholds 4.2.5 Counters, Interval Buckets and Thresholds
For physical-level events, there are counters, current 15-minute and For physical-level events, there are counters, current 15-minute and
one (up to 96) 15-minute history bucket(s) of "interval-counters", as one (up to 96) 15-minute history bucket(s) of "interval-counters", as
well as current and previous 1-day interval-counters. Threshold well as current and previous 1-day interval-counters. Threshold
notification can be configured for each physical-layer current notification can be configured for each physical-layer current 15-
15-minute bucket. minute bucket.
There is no requirement for an agent to ensure fixed relationship There is no requirement for an agent to ensure fixed relationship
between the start of a fifteen minute and any wall clock; however between the start of a fifteen minute and any wall clock; however
some implementations may align the fifteen-minute intervals with some implementations may align the fifteen-minute intervals with
quarter hours. Likewise, an implementation may choose to align one quarter hours. Likewise, an implementation may choose to align one
day intervals with start of a day. day intervals with start of a day.
Separate tables are provided for the 96 interval-counters. They are Separate tables are provided for the 96 interval-counters. They are
indexed by {ifIndex, AdslAtu*IntervalNumber}. indexed by {ifIndex, AdslAtu*IntervalNumber}.
Counters are not reset when an ATU-C or ATU-R is reinitialized, only Counters are not reset when an ATU-C or ATU-R is reinitialized, only
when the agent is reset or reinitialized (or under specific request when the agent is reset or reinitialized (or under specific request
outside the scope of this MIB). outside the scope of this MIB).
The 15-minute event counters are of type PerfCurrentCount and The 15-minute event counters are of the type PerfCurrentCount and
PerfIntervalCount. The 1-day event counters are of type PerfIntervalCount. The 1-day event counters are of the type
AdslPerfCurrDayCount and AdslPerfPrevDayCount. Both 15-minute and 1- AdslPerfCurrDayCount and AdslPerfPrevDayCount. Both 15-minute and 1-
day time elapsed counters are of type AdslPerfTimeElapsed. day time elapsed counters are of the type AdslPerfTimeElapsed.
4.2.6 Alternative profile configuration for the dual line mode 4.2.6 Alternative profile configuration for the dual line mode interface
interface
The object, adslLineConfProfileDualLite, is used only when the interface The object, adslLineConfProfileDualLite, is used only when the
(the ADSL line and, if applicable, channel) is configured as dual mode, interface (the ADSL line and, if applicable, channel) is configured
that is, the object adslLineTransAtucConfig is configured with one or as dual mode, that is, the object adslLineTransAtucConfig is
more full-rate modes and one or more G.Lite modes. configured with one or more full-rate modes and one or more G.Lite
modes.
The object adslLineConfProfile defined in ADSL-MIB [RFC2662] is used as The object adslLineConfProfile defined in ADSL-MIB [RFC2662] is used
the primary full-rate profile. The newly added object in this MIB as the primary full-rate profile. The newly added object in this MIB
module, adslLineConfProfileDualLite, is used to describe and configure module, adslLineConfProfileDualLite, is used to describe and
the G.Lite profile. Note that if one or more full-rate modes are configure the G.Lite profile. Note that if one or more full-rate
configured, or only G.Lite modes are configured, only the original modes are configured, or only G.Lite modes are configured, only the
full-rate profile is needed. The dual-mode profile object is only original full-rate profile is needed. The dual-mode profile object
needed when both full-rate and G.Lite profiles are needed. In this is only needed when both full-rate and G.Lite profiles are needed.
case, it will be set to the value of adslLineConfProfile when 'dynamic' In this case, it will be set to the value of adslLineConfProfile when
profiles are implemented. 'dynamic' profiles are implemented.
When 'static' profiles are implemented, however, similar to the case When 'static' profiles are implemented, however, similar to the case
of the object, adslLineConfProfileName [RFC2662], this object's value of the object, adslLineConfProfileName [RFC2662], this object's value
will need to algorithmically represent the line. In this case, the will need to algorithmically represent the line. In this case, the
value of the line's ifIndex plus a value indicating the line mode type value of the line's ifIndex plus a value indicating the line mode
(e.g., G.Lite, Full-rate) will be used. Therefore, the profile's name type (e.g., G.Lite, Full-rate) will be used. Therefore, the
is a string of the concatenation of ifIndex and one of the follow profile's name is a string of the concatenation of the ifIndex and
values: Full or Lite. This string will be fixed-length (i.e., 14) with one of the following values: Full or Lite. This string will be
leading zero(s). For example, the profile name for ifIndex that fixed-length (i.e., 14) with leading zero(s). For example, the
equals '15' and is a full rate line, it will be '0000000015Full'. profile name for ifIndex that equals '15' and is a full rate line
will be '0000000015Full'.
5. Conformance and Compliance 5. Conformance and Compliance
See the conformance and compliance statements within the information See the conformance and compliance statements within the information
module. module.
6. Definitions 6. Definitions
ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter32,
Integer32,
NOTIFICATION-TYPE,
MODULE-IDENTITY,
OBJECT-TYPE FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
TEXTUAL-CONVENTION FROM SNMPv2-TC
PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB
AdslPerfCurrDayCount,
AdslPerfPrevDayCount FROM ADSL-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
adslLineAlarmConfProfileEntry,
adslLineConfProfileEntry,
adslAturIntervalEntry,
adslAturPerfDataEntry,
adslAtucIntervalEntry,
adslAtucPerfDataEntry,
adslLineEntry,
adslMIB FROM ADSL-LINE-MIB
;
adslExtMIB MODULE-IDENTITY
LAST-UPDATED "200204231200Z" ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN
ORGANIZATION "IETF ADSL MIB Working Group" IMPORTS
Counter32,
Integer32,
NOTIFICATION-TYPE,
MODULE-IDENTITY,
OBJECT-TYPE FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
TEXTUAL-CONVENTION FROM SNMPv2-TC
PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB
AdslPerfCurrDayCount,
AdslPerfPrevDayCount FROM ADSL-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
adslLineAlarmConfProfileEntry,
adslLineConfProfileEntry,
adslAturIntervalEntry,
adslAturPerfDataEntry,
adslAtucIntervalEntry,
adslAtucPerfDataEntry,
adslLineEntry,
adslMIB FROM ADSL-LINE-MIB
;
CONTACT-INFO adslExtMIB MODULE-IDENTITY
"
Faye Ly
Pedestal Networks
3045 Park Boulevard
Palo Alto, CA 94306
Tel: +1 650-475-1274
Fax: +1 650-688-3119
E-Mail: faye@pedestalnetworks.com
Gregory Bathrick LAST-UPDATED "200212100000Z" -- 10 Dec 2002
NOKIA High Speed Access Nodes
1310 Redwood Way,
Petaluma, CA 94954
Tel: +1 707-793-7030
Fax: +1 707-792-0850
E-Mail: greg.bathrick@nokia.com
IETF ADSL MIB Working Group
<XDSLMIB@LISTSERV.ECIRALEIGH.COM>
"
DESCRIPTION
"This MIB Module is a supplement to the ADSL-LINE-MIB
[RFC2662]."
REVISION "200204231200Z"
DESCRIPTION "Initial Version, published as RFC xxxx. This MIB
module supplements the ADSL-LINE-MIB [RFC2662]."
::= { adslMIB 3 }
adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 } ORGANIZATION "IETF ADSL MIB Working Group"
AdslTransmissionModeType ::= TEXTUAL-CONVENTION CONTACT-INFO
STATUS current "
DESCRIPTION Faye Ly
"A set of ADSL line transmission modes, with one bit Pedestal Networks
per mode. The notes (F) and (L) denote Full-Rate 6503 Dumbarton Circle,
and G.Lite respectively: Fremont, CA 94555
Bit 00 : Regional Std. (ANSI T1.413) (F) Tel: +1 510-578-0158
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Fax: +1 510-744-5152
Bit 02 : G.992.1 POTS non-overlapped (F) E-Mail: faye@pedestalnetworks.com
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F)
"
SYNTAX BITS {
ansit1413(0),
etsi(1),
q9921PotsNonOverlapped(2),
q9921PotsOverlapped(3),
q9921IsdnNonOverlapped(4),
q9921isdnOverlapped(5),
q9921tcmIsdnNonOverlapped(6),
q9921tcmIsdnOverlapped(7),
q9922potsNonOverlapeed(8),
q9922potsOverlapped(9),
q9922tcmIsdnNonOverlapped(10),
q9922tcmIsdnOverlapped(11),
q9921tcmIsdnSymmetric(12)
}
adslLineExtTable OBJECT-TYPE Gregory Bathrick
SYNTAX SEQUENCE OF AdslLineExtEntry Nokia Networks
MAX-ACCESS not-accessible 2235 Mercury Way,
STATUS current Fax: +1 707-535-7300
DESCRIPTION E-Mail: greg.bathrick@nokia.com
"This table is an extension of RFC 2662. It
contains ADSL line configuration and
monitoring information. This includes the ADSL
line's capabilities and actual ADSL transmission
system."
::= { adslExtMibObjects 17 }
adslLineExtEntry OBJECT-TYPE General Discussion:adslmib@ietf.org
SYNTAX AdslLineExtEntry To Subscribe: https://www1.ietf.org/mailman/listinfo/adslmib
MAX-ACCESS not-accessible Archive: https://www1.ietf.org/mailman/listinfo/adslmib
STATUS current "
DESCRIPTION DESCRIPTION
"An entry extends the adslLineEntry defined in "Copyright (C) The Internet Society (2002). This version of
[RFC2662]. Each entry corresponds to an ADSL this MIB module is part of RFC 3440; see the RFC itself for
line." full legal notices.
AUGMENTS { adslLineEntry }
::= { adslLineExtTable 1 }
AdslLineExtEntry ::= This MIB Module is a supplement to the ADSL-LINE-MIB
SEQUENCE { [RFC2662]."
adslLineTransAtucCap AdslTransmissionModeType,
adslLineTransAtucConfig AdslTransmissionModeType,
adslLineTransAtucActual AdslTransmissionModeType,
adslLineGlitePowerState INTEGER,
adslLineConfProfileDualLite SnmpAdminString
}
adslLineTransAtucCap OBJECT-TYPE REVISION "200212100000Z" -- 10 dec 2002
SYNTAX AdslTransmissionModeType DESCRIPTION "Initial Version, published as RFC 3440. This MIB
MAX-ACCESS read-only module supplements the ADSL-LINE-MIB [RFC2662]."
STATUS current ::= { adslMIB 3 }
DESCRIPTION
"The transmission modes, represented by a
bitmask that the ATU-C is capable of
supporting. The modes available are limited
by the design of the equipment."
REFERENCE "Section 7.3.2 ITU G.997.1"
::= { adslLineExtEntry 1 }
adslLineTransAtucConfig OBJECT-TYPE adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 }
SYNTAX AdslTransmissionModeType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The transmission modes, represented by a bitmask,
currently enabled by the ATU-C. The manager can
only set those modes that are supported by the
ATU-C. An ATU-C's supported modes are provided by
AdslLineTransAtucCap."
REFERENCE "Section 7.3.2 ITU G.997.1"
::= { adslLineExtEntry 2 }
adslLineTransAtucActual OBJECT-TYPE AdslTransmissionModeType ::= TEXTUAL-CONVENTION
SYNTAX AdslTransmissionModeType STATUS current
MAX-ACCESS read-only DESCRIPTION
STATUS current "A set of ADSL line transmission modes, with one bit
DESCRIPTION per mode. The notes (F) and (L) denote Full-Rate
"The actual transmission mode of the ATU-C. and G.Lite respectively:
During ADSL line initialization, the ADSL Bit 00 : Regional Std. (ANSI T1.413) (F)
Transceiver Unit - Remote terminal end (ATU-R) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
will determine the mode used for the link. Bit 02 : G.992.1 POTS non-overlapped (F)
This value will be limited a single transmission Bit 03 : G.992.1 POTS overlapped (F)
mode that is a subset of those modes enabled Bit 04 : G.992.1 ISDN non-overlapped (F)
by the ATU-C and denoted by adslLineTransAtucConfig. Bit 05 : G.992.1 ISDN overlapped (F)
After an initialization has occurred, its mode is Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
saved as the 'Current' mode and is persistence Bit 07 : G.992.1 TCM-ISDN overlapped (F)
should the link go down. This object returns 0 Bit 08 : G.992.2 POTS non-overlapped (L)
(i.e. BITS with no mode bit set) if the mode is Bit 09 : G.992.2 POTS overlapped (L)
not known." Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
REFERENCE "Section 7.3.2 ITU G.997.1 " Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
::= { adslLineExtEntry 3 } Bit 12 : G.992.1 TCM-ISDN symmetric (F)
"
SYNTAX BITS {
ansit1413(0),
etsi(1),
q9921PotsNonOverlapped(2),
q9921PotsOverlapped(3),
q9921IsdnNonOverlapped(4),
q9921isdnOverlapped(5),
q9921tcmIsdnNonOverlapped(6),
q9921tcmIsdnOverlapped(7),
q9922potsNonOverlapeed(8),
q9922potsOverlapped(9),
q9922tcmIsdnNonOverlapped(10),
q9922tcmIsdnOverlapped(11),
q9921tcmIsdnSymmetric(12)
}
adslLineGlitePowerState OBJECT-TYPE adslLineExtTable OBJECT-TYPE
SYNTAX INTEGER { SYNTAX SEQUENCE OF AdslLineExtEntry
none(1), MAX-ACCESS not-accessible
l0(2), -- L0 Power on STATUS current
l1(3), -- L1 Power on but reduced DESCRIPTION
l3(4) -- L3 Power off "This table is an extension of RFC 2662. It
} contains ADSL line configuration and
MAX-ACCESS read-only monitoring information. This includes the ADSL
STATUS current line's capabilities and actual ADSL transmission
DESCRIPTION system."
"The value of this object specifies the power ::= { adslExtMibObjects 17 }
state of this interface. L0 is power on, L1 is
power on but reduced and L3 is power off. Power
state cannot be configured by an operator but it
can be viewed via the ifOperStatus object for the
managed ADSL interface. The value of the object
ifOperStatus is set to down(2) if the ADSL interface
is in power state L3 and is set to up(1) if the ADSL
line interface is in power state L0 or L1. If the
object adslLineTransAtucActual is set to a G.992.2
(G.Lite)-type transmission mode, the value of
this object will be one of the valid power
states: L0(2), L1(3), or L3(4). Otherwise, its
value will be none(1)."
::= { adslLineExtEntry 4 }
adslLineConfProfileDualLite OBJECT-TYPE adslLineExtEntry OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX AdslLineExtEntry
MAX-ACCESS read-write MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object extends the definition an ADSL line and "An entry extends the adslLineEntry defined in
associated channels (when applicable) for cases when [RFC2662]. Each entry corresponds to an ADSL
it is configured in dual mode, and operating in a line."
G.Lite-type mode as denoted by AUGMENTS { adslLineEntry }
adslLineTransAtucActual. Dual mode exists when the ::= { adslLineExtTable 1 }
object, adslLineTransAtucConfig, is configured with
one or more full-rate modes and one or more G.Lite
modes simultaneously.
When 'dynamic' profiles are implemented, the value of AdslLineExtEntry ::=
object is equal to the index of the applicable row in SEQUENCE {
the ADSL Line Configuration Profile Table, adslLineTransAtucCap AdslTransmissionModeType,
AdslLineConfProfileTable defined in ADSL-MIB adslLineTransAtucConfig AdslTransmissionModeType,
[RFC2662]. adslLineTransAtucActual AdslTransmissionModeType,
adslLineGlitePowerState INTEGER,
adslLineConfProfileDualLite SnmpAdminString
}
In the case when dual-mode has not been enabled, the adslLineTransAtucCap OBJECT-TYPE
value of the object will be equal to the value of the SYNTAX AdslTransmissionModeType
object adslLineConfProfile [RFC2662]. MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transmission modes, represented by a
bitmask that the ATU-C is capable of
supporting. The modes available are limited
by the design of the equipment."
REFERENCE "Section 7.3.2 ITU G.997.1"
::= { adslLineExtEntry 1 }
When `static' profiles are implemented, in much adslLineTransAtucConfig OBJECT-TYPE
like the case of the object, adslLineConfProfileName SYNTAX AdslTransmissionModeType
[RFC2662], this object's value will need to MAX-ACCESS read-write
algorithmically represent the characteristics of the STATUS current
line. In this case, the value of the line's ifIndex
plus a value indicating the line mode type
(e.g., G.Lite, Full-rate) will be used. Therefore,
the profile's name is a string concatenating the
ifIndex and one of the follow values: Full or Lite.
This string will be fixed-length (i.e., 14) with
leading zero(s). For example, the profile name for
ifIndex that equals '15' and is a full rate line, it
will be '0000000015Full'."
REFERENCE "Section 5.4 Profiles, RFC 2662"
::= { adslLineExtEntry 5 }
adslAtucPerfDataExtTable OBJECT-TYPE DESCRIPTION
SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry "The transmission modes, represented by a bitmask,
MAX-ACCESS not-accessible currently enabled by the ATU-C. The manager can
STATUS current only set those modes that are supported by the
DESCRIPTION ATU-C. An ATU-C's supported modes are provided by
"This table extends adslAtucPerfDataTable [RFC2662] AdslLineTransAtucCap."
with additional ADSL physical line counter REFERENCE "Section 7.3.2 ITU G.997.1"
information such as unavailable seconds-line and ::= { adslLineExtEntry 2 }
severely errored seconds-line."
::= { adslExtMibObjects 18 }
adslAtucPerfDataExtEntry OBJECT-TYPE adslLineTransAtucActual OBJECT-TYPE
SYNTAX AdslAtucPerfDataExtEntry SYNTAX AdslTransmissionModeType
MAX-ACCESS not-accessible MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry extends the adslAtucPerfDataEntry defined "The actual transmission mode of the ATU-C.
in [RFC2662]. Each entry corresponds to an ADSL During ADSL line initialization, the ADSL
line." Transceiver Unit - Remote terminal end (ATU-R)
AUGMENTS { adslAtucPerfDataEntry } will determine the mode used for the link.
::= { adslAtucPerfDataExtTable 1 } This value will be limited a single transmission
mode that is a subset of those modes enabled
by the ATU-C and denoted by
adslLineTransAtucConfig. After an initialization
has occurred, its mode is saved as the 'Current'
mode and is persistence should the link go
down. This object returns 0 (i.e. BITS with no
mode bit set) if the mode is not known."
REFERENCE "Section 7.3.2 ITU G.997.1 "
::= { adslLineExtEntry 3 }
AdslAtucPerfDataExtEntry ::= adslLineGlitePowerState OBJECT-TYPE
SEQUENCE { SYNTAX INTEGER {
adslAtucPerfStatFastR Counter32, none(1),
adslAtucPerfStatFailedFastR Counter32, l0(2), -- L0 Power on
adslAtucPerfStatSesL Counter32, l1(3), -- L1 Power on but reduced
adslAtucPerfStatUasL Counter32, l3(4) -- L3 Power off
adslAtucPerfCurr15MinFastR PerfCurrentCount, }
adslAtucPerfCurr15MinFailedFastR PerfCurrentCount, MAX-ACCESS read-only
adslAtucPerfCurr15MinSesL PerfCurrentCount, STATUS current
adslAtucPerfCurr15MinUasL PerfCurrentCount, DESCRIPTION
adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount, "The value of this object specifies the power
adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount, state of this interface. L0 is power on, L1 is
adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount, power on but reduced and L3 is power off. Power
adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount, state cannot be configured by an operator but it
adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount, can be viewed via the ifOperStatus object for the
adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount, managed ADSL interface. The value of the object
adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount, ifOperStatus is set to down(2) if the ADSL
adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount interface is in power state L3 and is set to up(1)
} if the ADSL line interface is in power state L0 or
L1. If the object adslLineTransAtucActual is set to
a G.992.2 (G.Lite)-type transmission mode, the
value of this object will be one of the valid power
states: L0(2), L1(3), or L3(4). Otherwise, its
value will be none(1)."
::= { adslLineExtEntry 4 }
adslAtucPerfStatFastR OBJECT-TYPE adslLineConfProfileDualLite OBJECT-TYPE
SYNTAX Counter32 SYNTAX SnmpAdminString
UNITS "line retrains" MAX-ACCESS read-write
MAX-ACCESS read-only STATUS current
STATUS current DESCRIPTION
DESCRIPTION "This object extends the definition an ADSL line and
"The value of this object reports the count of associated channels (when applicable) for cases
the number of fast line bs since last when it is configured in dual mode, and operating
agent reset." in a G.Lite-type mode as denoted by
REFERENCE "ITU G.997.1 Section 7.4.15.1 " adslLineTransAtucActual. Dual mode exists when the
::= { adslAtucPerfDataExtEntry 1 } object, adslLineTransAtucConfig, is configured with
one or more full-rate modes and one or more G.Lite
modes simultaneously.
adslAtucPerfStatFailedFastR OBJECT-TYPE When 'dynamic' profiles are implemented, the value
SYNTAX Counter32 of object is equal to the index of the applicable
UNITS "line retrains" row in the ADSL Line Configuration Profile Table,
MAX-ACCESS read-only AdslLineConfProfileTable defined in ADSL-MIB
STATUS current [RFC2662].
DESCRIPTION
"The value of this object reports the count of
the number of failed fast line retrains since
last agent reset."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 2 }
adslAtucPerfStatSesL OBJECT-TYPE In the case when dual-mode has not been enabled,
SYNTAX Counter32 the value of the object will be equal to the value
UNITS "seconds" of the object adslLineConfProfile [RFC2662].
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
the number of severely errored seconds-line since
last agent reset."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 3 }
adslAtucPerfStatUasL OBJECT-TYPE When `static' profiles are implemented, in much
SYNTAX Counter32 like the case of the object,
UNITS "seconds" adslLineConfProfileName [RFC2662], this object's
MAX-ACCESS read-only value will need to algorithmically represent the
STATUS current characteristics of the line. In this case, the
DESCRIPTION value of the line's ifIndex plus a value indicating
"The value of this object reports the count of the line mode type (e.g., G.Lite, Full-rate) will
the number of unavailable seconds-line since be used. Therefore, the profile's name is a string
last agent reset." concatenating the ifIndex and one of the follow
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " values: Full or Lite. This string will be
::= { adslAtucPerfDataExtEntry 4 } fixed-length (i.e., 14) with leading zero(s). For
example, the profile name for ifIndex that equals
'15' and is a full rate line, it will be
'0000000015Full'."
REFERENCE "Section 5.4 Profiles, RFC 2662"
::= { adslLineExtEntry 5 }
adslAtucPerfCurr15MinFastR OBJECT-TYPE adslAtucPerfDataExtTable OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAtucPerfCurr15MinFastR reports the current
number of seconds during which there have been
fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 5 }
adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry
SYNTAX PerfCurrentCount MAX-ACCESS not-accessible
UNITS "seconds" STATUS current
MAX-ACCESS read-only DESCRIPTION
STATUS current "This table extends adslAtucPerfDataTable [RFC2662]
DESCRIPTION with additional ADSL physical line counter
"For the current 15-minute interval, information such as unavailable seconds-line and
adslAtucPerfCurr15MinFailedFastR reports the current severely errored seconds-line."
number of seconds during which there have been ::= { adslExtMibObjects 18 }
failed fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 6 }
adslAtucPerfCurr15MinSesL OBJECT-TYPE adslAtucPerfDataExtEntry OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX AdslAtucPerfDataExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-only STATUS current
STATUS current DESCRIPTION
DESCRIPTION "An entry extends the adslAtucPerfDataEntry defined
"For the current 15-minute interval, in [RFC2662]. Each entry corresponds to an ADSL
adslAtucPerfCurr15MinSesL reports the current line."
number of seconds during which there have been AUGMENTS { adslAtucPerfDataEntry }
severely errored seconds-line." ::= { adslAtucPerfDataExtTable 1 }
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 7 }
adslAtucPerfCurr15MinUasL OBJECT-TYPE AdslAtucPerfDataExtEntry ::=
SYNTAX PerfCurrentCount SEQUENCE {
UNITS "seconds" adslAtucPerfStatFastR Counter32,
MAX-ACCESS read-only adslAtucPerfStatFailedFastR Counter32,
STATUS current adslAtucPerfStatSesL Counter32,
DESCRIPTION adslAtucPerfStatUasL Counter32,
"For the current 15-minute interval, adslAtucPerfCurr15MinFastR PerfCurrentCount,
adslAtucPerfCurr15MinUasL reports the current adslAtucPerfCurr15MinFailedFastR PerfCurrentCount,
number of seconds during which there have been adslAtucPerfCurr15MinSesL PerfCurrentCount,
unavailable seconds-line." adslAtucPerfCurr15MinUasL PerfCurrentCount,
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount,
::= { adslAtucPerfDataExtEntry 8 } adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount,
adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount,
adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount,
adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount,
adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount,
adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount,
adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount
}
adslAtucPerfCurr1DayFastR OBJECT-TYPE adslAtucPerfStatFastR OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount SYNTAX Counter32
UNITS "seconds" UNITS "line retrains"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current day as measured by "The value of this object reports the count of
adslAtucPerfCurr1DayTimeElapsed [RFC2662], the number of fast line bs since last
adslAtucPerfCurr1DayFastR reports the number agent reset."
of seconds during which there have been
fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 9 }
adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE REFERENCE "ITU G.997.1 Section 7.4.15.1 "
SYNTAX AdslPerfCurrDayCount ::= { adslAtucPerfDataExtEntry 1 }
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayFailedFastR reports the
number of seconds during which there have been
failed fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 10 }
adslAtucPerfCurr1DaySesL OBJECT-TYPE adslAtucPerfStatFailedFastR OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount SYNTAX Counter32
UNITS "seconds" UNITS "line retrains"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current day as measured by "The value of this object reports the count of
adslAtucPerfCurr1DayTimeElapsed [RFC2662], the number of failed fast line retrains since
adslAtucPerfCurr1DaySesL reports the last agent reset."
number of seconds during which there have been REFERENCE "ITU G.997.1 Section 7.4.15.2 "
severely errored seconds-line." ::= { adslAtucPerfDataExtEntry 2 }
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 11 }
adslAtucPerfCurr1DayUasL OBJECT-TYPE adslAtucPerfStatSesL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current day as measured by "The value of this object reports the count of
adslAtucPerfCurr1DayTimeElapsed [RFC2662], the number of severely errored seconds-line since
adslAtucPerfCurr1DayUasL reports the last agent reset."
number of seconds during which there have been REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
unavailable seconds-line." ::= { adslAtucPerfDataExtEntry 3 }
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 12 }
adslAtucPerfPrev1DayFastR OBJECT-TYPE adslAtucPerfStatUasL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayFastR "The value of this object reports the count of
reports the number of seconds during which there the number of unavailable seconds-line since
were fast retrains." last agent reset."
REFERENCE "ITU G.997.1 Section 7.4.15.1 " REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 13 } ::= { adslAtucPerfDataExtEntry 4 }
adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE adslAtucPerfCurr15MinFastR OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayFailedFastR "For the current 15-minute interval,
reports the number of seconds during which there adslAtucPerfCurr15MinFastR reports the current
were failed fast retrains." number of seconds during which there have been
REFERENCE "ITU G.997.1 Section 7.4.15.2 " fast retrains."
::= { adslAtucPerfDataExtEntry 14 } REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 5 }
adslAtucPerfPrev1DaySesL OBJECT-TYPE adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the previous day, adslAtucPerfPrev1DaySesL "For the current 15-minute interval,
reports the number of seconds during which there adslAtucPerfCurr15MinFailedFastR reports the
were severely errored seconds-line." current number of seconds during which there
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " have been failed fast retrains."
::= { adslAtucPerfDataExtEntry 15 } REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 6 }
adslAtucPerfPrev1DayUasL OBJECT-TYPE adslAtucPerfCurr15MinSesL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayUasL "For the current 15-minute interval,
reports the number of seconds during which there adslAtucPerfCurr15MinSesL reports the current
were unavailable seconds-line." number of seconds during which there have been
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " severely errored seconds-line."
::= { adslAtucPerfDataExtEntry 16 } REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 7 }
adslAtucIntervalExtTable OBJECT-TYPE adslAtucPerfCurr15MinUasL OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry SYNTAX PerfCurrentCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"This table provides one row for each ATU-C DESCRIPTION
performance data collection interval for "For the current 15-minute interval,
ADSL physical interfaces whose adslAtucPerfCurr15MinUasL reports the current
IfEntries' ifType is equal to adsl(94)." number of seconds during which there have been
::= { adslExtMibObjects 19 } unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 8 }
adslAtucIntervalExtEntry OBJECT-TYPE adslAtucPerfCurr1DayFastR OBJECT-TYPE
SYNTAX AdslAtucIntervalExtEntry SYNTAX AdslPerfCurrDayCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION "An entry in the STATUS current
adslAtucIntervalExtTable." DESCRIPTION
AUGMENTS { adslAtucIntervalEntry } "For the current day as measured by
::= { adslAtucIntervalExtTable 1 } adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayFastR reports the number
of seconds during which there have been
fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 9 }
AdslAtucIntervalExtEntry ::= adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE
SEQUENCE { SYNTAX AdslPerfCurrDayCount
adslAtucIntervalFastR PerfIntervalCount, UNITS "seconds"
adslAtucIntervalFailedFastR PerfIntervalCount, MAX-ACCESS read-only
adslAtucIntervalSesL PerfIntervalCount, STATUS current
adslAtucIntervalUasL PerfIntervalCount DESCRIPTION
} "For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayFailedFastR reports the
number of seconds during which there have been
failed fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 10 }
adslAtucIntervalFastR OBJECT-TYPE adslAtucPerfCurr1DaySesL OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX AdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current interval, adslAtucIntervalFastR "For the current day as measured by
reports the current number of seconds during which adslAtucPerfCurr1DayTimeElapsed [RFC2662],
there have been fast retrains." adslAtucPerfCurr1DaySesL reports the
::= { adslAtucIntervalExtEntry 1 } number of seconds during which there have been
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 11 }
adslAtucIntervalFailedFastR OBJECT-TYPE adslAtucPerfCurr1DayUasL OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX AdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the each interval, adslAtucIntervalFailedFastR "For the current day as measured by
reports the number of seconds during which adslAtucPerfCurr1DayTimeElapsed [RFC2662],
there have been failed fast retrains." adslAtucPerfCurr1DayUasL reports the
::= { adslAtucIntervalExtEntry 2 } number of seconds during which there have been
unavailable seconds-line."
adslAtucIntervalSesL OBJECT-TYPE REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
SYNTAX PerfIntervalCount ::= { adslAtucPerfDataExtEntry 12 }
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAtucIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line."
::= { adslAtucIntervalExtEntry 3 }
adslAtucIntervalUasL OBJECT-TYPE adslAtucPerfPrev1DayFastR OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX AdslPerfPrevDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the each interval, adslAtucIntervalUasL "For the previous day, adslAtucPerfPrev1DayFastR
reports the number of seconds during which reports the number of seconds during which there
there have been unavailable seconds-line." were fast retrains."
::= { adslAtucIntervalExtEntry 4 } REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 13 }
adslAturPerfDataExtTable OBJECT-TYPE adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry SYNTAX AdslPerfPrevDayCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"This table contains ADSL physical line counters DESCRIPTION
not defined in the adslAturPerfDataTable "For the previous day,
from the ADSL-LINE-MIB [RFC2662]." adslAtucPerfPrev1DayFailedFastR reports the number
::= { adslExtMibObjects 20 } of seconds during which there were failed fast
retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 14 }
adslAturPerfDataExtEntry OBJECT-TYPE adslAtucPerfPrev1DaySesL OBJECT-TYPE
SYNTAX AdslAturPerfDataExtEntry SYNTAX AdslPerfPrevDayCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"An entry extends the adslAturPerfDataEntry defined DESCRIPTION
in [RFC2662]. Each entry corresponds to an ADSL "For the previous day, adslAtucPerfPrev1DaySesL
line." reports the number of seconds during which there
AUGMENTS { adslAturPerfDataEntry } were severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 15 }
::= { adslAturPerfDataExtTable 1 } adslAtucPerfPrev1DayUasL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayUasL
reports the number of seconds during which there
were unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 16 }
AdslAturPerfDataExtEntry ::= adslAtucIntervalExtTable OBJECT-TYPE
SEQUENCE { SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry
adslAturPerfStatSesL Counter32, MAX-ACCESS not-accessible
adslAturPerfStatUasL Counter32, STATUS current
adslAturPerfCurr15MinSesL PerfCurrentCount, DESCRIPTION
adslAturPerfCurr15MinUasL PerfCurrentCount, "This table provides one row for each ATU-C
adslAturPerfCurr1DaySesL AdslPerfCurrDayCount, performance data collection interval for
adslAturPerfCurr1DayUasL AdslPerfCurrDayCount, ADSL physical interfaces whose
adslAturPerfPrev1DaySesL AdslPerfPrevDayCount, IfEntries' ifType is equal to adsl(94)."
adslAturPerfPrev1DayUasL AdslPerfPrevDayCount ::= { adslExtMibObjects 19 }
}
adslAturPerfStatSesL OBJECT-TYPE adslAtucIntervalExtEntry OBJECT-TYPE
SYNTAX Counter32 SYNTAX AdslAtucIntervalExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-only STATUS current
STATUS current DESCRIPTION "An entry in the
DESCRIPTION adslAtucIntervalExtTable."
"The value of this object reports the count of AUGMENTS { adslAtucIntervalEntry }
severely errored second-line since the last agent ::= { adslAtucIntervalExtTable 1 }
reset."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAturPerfDataExtEntry 1 }
adslAturPerfStatUasL OBJECT-TYPE AdslAtucIntervalExtEntry ::=
SYNTAX Counter32 SEQUENCE {
UNITS "seconds" adslAtucIntervalFastR PerfIntervalCount,
MAX-ACCESS read-only adslAtucIntervalFailedFastR PerfIntervalCount,
STATUS current adslAtucIntervalSesL PerfIntervalCount,
DESCRIPTION adslAtucIntervalUasL PerfIntervalCount
"The value of this object reports the count of }
unavailable seconds-line since the last agent
reset."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 2 }
adslAturPerfCurr15MinSesL OBJECT-TYPE adslAtucIntervalFastR OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current 15-minute interval, "For the current interval, adslAtucIntervalFastR
adslAturPerfCurr15MinSesL reports the current reports the current number of seconds during which
number of seconds during which there have been there have been fast retrains."
severely errored seconds-line." ::= { adslAtucIntervalExtEntry 1 }
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " adslAtucIntervalFailedFastR OBJECT-TYPE
::= { adslAturPerfDataExtEntry 3 } SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAtucIntervalFailedFastR
reports the number of seconds during which
there have been failed fast retrains."
::= { adslAtucIntervalExtEntry 2 }
adslAturPerfCurr15MinUasL OBJECT-TYPE adslAtucIntervalSesL OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current 15-minute interval, "For the each interval, adslAtucIntervalSesL
adslAturPerfCurr15MinUasL reports the current reports the number of seconds during which
number of seconds during which there have been there have been severely errored seconds-line."
available seconds-line." ::= { adslAtucIntervalExtEntry 3 }
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 4 }
adslAturPerfCurr1DaySesL OBJECT-TYPE adslAtucIntervalUasL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the current day as measured by "For the each interval, adslAtucIntervalUasL
adslAturPerfCurr1DayTimeElapsed [RFC2662], reports the number of seconds during which
adslAturPerfCurr1DaySesL reports the there have been unavailable seconds-line."
number of seconds during which there have been ::= { adslAtucIntervalExtEntry 4 }
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 5 }
adslAturPerfCurr1DayUasL OBJECT-TYPE adslAturPerfDataExtTable OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-only STATUS current
STATUS current DESCRIPTION
DESCRIPTION "This table contains ADSL physical line counters
"For the current day as measured by not defined in the adslAturPerfDataTable
adslAturPerfCurr1DayTimeElapsed [RFC2662], from the ADSL-LINE-MIB [RFC2662]."
adslAturPerfCurr1DayUasL reports the ::= { adslExtMibObjects 20 }
number of seconds during which there have been
unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 6 }
adslAturPerfPrev1DaySesL OBJECT-TYPE adslAturPerfDataExtEntry OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX AdslAturPerfDataExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-only STATUS current
STATUS current DESCRIPTION
DESCRIPTION "An entry extends the adslAturPerfDataEntry defined
"For the previous day, adslAturPerfPrev1DaySesL in [RFC2662]. Each entry corresponds to an ADSL
reports the number of seconds during which there line."
were severely errored seconds-line." AUGMENTS { adslAturPerfDataEntry }
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtTable 1 }
::= { adslAturPerfDataExtEntry 7 } AdslAturPerfDataExtEntry ::=
SEQUENCE {
adslAturPerfStatSesL Counter32,
adslAturPerfStatUasL Counter32,
adslAturPerfCurr15MinSesL PerfCurrentCount,
adslAturPerfCurr15MinUasL PerfCurrentCount,
adslAturPerfCurr1DaySesL AdslPerfCurrDayCount,
adslAturPerfCurr1DayUasL AdslPerfCurrDayCount,
adslAturPerfPrev1DaySesL AdslPerfPrevDayCount,
adslAturPerfPrev1DayUasL AdslPerfPrevDayCount
}
adslAturPerfPrev1DayUasL OBJECT-TYPE adslAturPerfStatSesL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the previous day, adslAturPerfPrev1DayUasL "The value of this object reports the count of
reports the number of seconds during which there severely errored second-line since the last agent
were severely errored seconds-line." reset."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAturPerfDataExtEntry 8 } ::= { adslAturPerfDataExtEntry 1 }
adslAturIntervalExtTable OBJECT-TYPE adslAturPerfStatUasL OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturIntervalExtEntry SYNTAX Counter32
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"This table provides one row for each ATU-R DESCRIPTION
performance data collection interval for "The value of this object reports the count of
ADSL physical interfaces whose unavailable seconds-line since the last agent
IfEntries' ifType is equal to adsl(94)." reset."
::= { adslExtMibObjects 21 } REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 2 }
adslAturIntervalExtEntry OBJECT-TYPE adslAturPerfCurr15MinSesL OBJECT-TYPE
SYNTAX AdslAturIntervalExtEntry SYNTAX PerfCurrentCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION "An entry in the STATUS current
adslAturIntervalExtTable." DESCRIPTION
AUGMENTS { adslAturIntervalEntry } "For the current 15-minute interval,
::= { adslAturIntervalExtTable 1 } adslAturPerfCurr15MinSesL reports the current
number of seconds during which there have been
severely errored seconds-line."
AdslAturIntervalExtEntry ::= REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
SEQUENCE {
adslAturIntervalSesL PerfIntervalCount,
adslAturIntervalUasL PerfIntervalCount
}
adslAturIntervalSesL OBJECT-TYPE ::= { adslAturPerfDataExtEntry 3 }
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAturIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line."
::= { adslAturIntervalExtEntry 1 }
adslAturIntervalUasL OBJECT-TYPE adslAturPerfCurr15MinUasL OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For the each interval, adslAturIntervalUasL "For the current 15-minute interval,
reports the number of seconds during which adslAturPerfCurr15MinUasL reports the current
there have been unavailable seconds-line." number of seconds during which there have been
::= { adslAturIntervalExtEntry 2 } available seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 4 }
adslConfProfileExtTable OBJECT-TYPE adslAturPerfCurr1DaySesL OBJECT-TYPE
SYNTAX SEQUENCE OF AdslConfProfileExtEntry SYNTAX AdslPerfCurrDayCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"The adslConfProfileExtTable extends the ADSL line DESCRIPTION
profile configuration information in the "For the current day as measured by
adslLineConfProfileTable from the ADSL-LINE-MIB adslAturPerfCurr1DayTimeElapsed [RFC2662],
[RFC2662] by adding the ability to configure the adslAturPerfCurr1DaySesL reports the
ADSL physical line mode." number of seconds during which there have been
::= { adslExtMibObjects 22 } severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 5 }
adslConfProfileExtEntry OBJECT-TYPE adslAturPerfCurr1DayUasL OBJECT-TYPE
SYNTAX AdslConfProfileExtEntry SYNTAX AdslPerfCurrDayCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"An entry extends the adslLineConfProfileEntry defined DESCRIPTION
in [RFC2662]. Each entry corresponds to an ADSL line "For the current day as measured by
profile." adslAturPerfCurr1DayTimeElapsed [RFC2662],
AUGMENTS { adslLineConfProfileEntry } adslAturPerfCurr1DayUasL reports the
::= { adslConfProfileExtTable 1 } number of seconds during which there have been
unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 6 }
AdslConfProfileExtEntry ::= adslAturPerfPrev1DaySesL OBJECT-TYPE
SEQUENCE { SYNTAX AdslPerfPrevDayCount
adslConfProfileLineType INTEGER UNITS "seconds"
} MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAturPerfPrev1DaySesL
reports the number of seconds during which there
were severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 7 }
adslConfProfileLineType OBJECT-TYPE adslAturPerfPrev1DayUasL OBJECT-TYPE
SYNTAX INTEGER { SYNTAX AdslPerfPrevDayCount
noChannel (1), -- no channels exist UNITS "seconds"
fastOnly (2), -- only fast channel exists MAX-ACCESS read-only
interleavedOnly (3), -- only interleaved channel STATUS current
-- exist DESCRIPTION
fastOrInterleaved (4),-- either fast or interleaved "For the previous day, adslAturPerfPrev1DayUasL
-- channels can exist, but reports the number of seconds during which there
-- only one at any time were severely errored seconds-line."
fastAndInterleaved (5)-- both the fast channel and REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
-- the interleaved channel ::= { adslAturPerfDataExtEntry 8 }
-- exist
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to configure the ADSL physical
line mode. It has following valid values:
noChannel(1), when no channels exist. adslAturIntervalExtTable OBJECT-TYPE
fastOnly(2), when only fast channel exists. SYNTAX SEQUENCE OF AdslAturIntervalExtEntry
interleavedOnly(3), when only interleaved channel MAX-ACCESS not-accessible
exist. STATUS current
fastOrInterleaved(4), when either fast or DESCRIPTION
interleaved channels can exist, but only one "This table provides one row for each ATU-R
at any time. performance data collection interval for
fastAndInterleaved(5), when both the fast channel ADSL physical interfaces whose
and the interleaved channel exist. IfEntries' ifType is equal to adsl(94)."
::= { adslExtMibObjects 21 }
In the case when no value has been set, the default adslAturIntervalExtEntry OBJECT-TYPE
Value is noChannel(1). SYNTAX AdslAturIntervalExtEntry
" MAX-ACCESS not-accessible
DEFVAL { fastOnly } STATUS current
::= { adslConfProfileExtEntry 1 } DESCRIPTION "An entry in the
adslAturIntervalExtTable."
AUGMENTS { adslAturIntervalEntry }
::= { adslAturIntervalExtTable 1 }
adslAlarmConfProfileExtTable OBJECT-TYPE AdslAturIntervalExtEntry ::=
SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry SEQUENCE {
MAX-ACCESS not-accessible adslAturIntervalSesL PerfIntervalCount,
STATUS current adslAturIntervalUasL PerfIntervalCount
DESCRIPTION }
"This table extends the adslLineAlarmConfProfileTable
and provides threshold parameters for all the
counters defined in this MIB module."
::= { adslExtMibObjects 23 }
adslAlarmConfProfileExtEntry OBJECT-TYPE adslAturIntervalSesL OBJECT-TYPE
SYNTAX AdslAlarmConfProfileExtEntry SYNTAX PerfIntervalCount
MAX-ACCESS not-accessible UNITS "seconds"
STATUS current MAX-ACCESS read-only
DESCRIPTION STATUS current
"An entry extends the adslLineAlarmConfProfileTable DESCRIPTION
defined in [RFC2662]. Each entry corresponds to "For the each interval, adslAturIntervalSesL
an ADSL alarm profile." reports the number of seconds during which
AUGMENTS { adslLineAlarmConfProfileEntry } there have been severely errored seconds-line."
::= { adslAlarmConfProfileExtTable 1 } ::= { adslAturIntervalExtEntry 1 }
AdslAlarmConfProfileExtEntry ::= adslAturIntervalUasL OBJECT-TYPE
SEQUENCE { SYNTAX PerfIntervalCount
adslAtucThreshold15MinFailedFastR Integer32, UNITS "seconds"
adslAtucThreshold15MinSesL Integer32, MAX-ACCESS read-only
adslAtucThreshold15MinUasL Integer32, STATUS current
adslAturThreshold15MinSesL Integer32, DESCRIPTION
adslAturThreshold15MinUasL Integer32 "For the each interval, adslAturIntervalUasL
} reports the number of seconds during which
there have been unavailable seconds-line."
::= { adslAturIntervalExtEntry 2 }
adslAtucThreshold15MinFailedFastR OBJECT-TYPE adslConfProfileExtTable OBJECT-TYPE
SYNTAX Integer32(0..900) SYNTAX SEQUENCE OF AdslConfProfileExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-create STATUS current
STATUS current DESCRIPTION
DESCRIPTION "The adslConfProfileExtTable extends the ADSL line
"The first time the value of the corresponding profile configuration information in the
instance of adslAtucPerfCurr15MinFailedFastR reaches adslLineConfProfileTable from the ADSL-LINE-MIB
or exceeds this value within a given 15-minute [RFC2662] by adding the ability to configure the
performance data collection period, an ADSL physical line mode."
adslAtucFailedFastRThreshTrap notification will ::= { adslExtMibObjects 22 }
be generated. The value '0' will disable the
notification. The default value of this object is
'0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 1 }
adslAtucThreshold15MinSesL OBJECT-TYPE adslConfProfileExtEntry OBJECT-TYPE
SYNTAX Integer32(0..900) SYNTAX AdslConfProfileExtEntry
UNITS "seconds" MAX-ACCESS not-accessible
MAX-ACCESS read-create STATUS current
STATUS current DESCRIPTION
DESCRIPTION "An entry extends the adslLineConfProfileEntry
"The first time the value of the corresponding instance defined in [RFC2662]. Each entry corresponds to an
of adslAtucPerf15MinSesL reaches or exceeds ADSL line profile."
this value within a given 15-minute performance data AUGMENTS { adslLineConfProfileEntry }
collection period, an adslAtucSesLThreshTrap ::= { adslConfProfileExtTable 1 }
notification will be generated. The value '0' will
disable the notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 2 } AdslConfProfileExtEntry ::=
SEQUENCE {
adslConfProfileLineType INTEGER
}
adslAtucThreshold15MinUasL OBJECT-TYPE adslConfProfileLineType OBJECT-TYPE
SYNTAX Integer32(0..900) SYNTAX INTEGER {
UNITS "seconds" noChannel (1), -- no channels exist
MAX-ACCESS read-create fastOnly (2), -- only fast channel exists
STATUS current interleavedOnly (3), -- only interleaved channel
DESCRIPTION -- exist
"The first time the value of the corresponding instance fastOrInterleaved (4),-- either fast or interleaved
of adslAtucPerf15MinUasL reaches or exceeds -- channels can exist, but
this value within a given 15-minute performance data -- only one at any time
collection period, an adslAtucUasLThreshTrap fastAndInterleaved (5)-- both the fast channel and
notification will be generated. The value '0' will -- the interleaved channel
disable the notification. The default value of this -- exist
object is '0'." }
DEFVAL { 0 } MAX-ACCESS read-create
::= { adslAlarmConfProfileExtEntry 3 } STATUS current
DESCRIPTION
"This object is used to configure the ADSL physical
line mode. It has following valid values:
adslAturThreshold15MinSesL OBJECT-TYPE noChannel(1), when no channels exist.
SYNTAX Integer32(0..900) fastOnly(2), when only fast channel exists.
UNITS "seconds" interleavedOnly(3), when only interleaved channel
MAX-ACCESS read-create exist.
STATUS current fastOrInterleaved(4), when either fast or
DESCRIPTION interleaved channels can exist, but only one
"The first time the value of the corresponding instance at any time.
of adslAturPerf15MinSesL reaches or exceeds fastAndInterleaved(5), when both the fast channel
this value within a given 15-minute performance data and the interleaved channel exist.
collection period, an adslAturSesLThreshTrap
notification will be generated. The value '0' will
disable the notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 4 }
adslAturThreshold15MinUasL OBJECT-TYPE In the case when no value has been set, the default
SYNTAX Integer32(0..900) Value is noChannel(1).
UNITS "seconds" "
MAX-ACCESS read-create DEFVAL { fastOnly }
STATUS current ::= { adslConfProfileExtEntry 1 }
DESCRIPTION
"The first time the value of the corresponding instance
of adslAturPerf15MinUasL reaches or exceeds
this value within a given 15-minute performance data
collection period, an adslAturUasLThreshTrap
notification will be generated. The value '0' will
disable the notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 5 } adslAlarmConfProfileExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the
adslLineAlarmConfProfileTable and provides
threshold parameters for all the counters defined
in this MIB module."
::= { adslExtMibObjects 23 }
-- definitions adslAlarmConfProfileExtEntry OBJECT-TYPE
SYNTAX AdslAlarmConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslLineAlarmConfProfileTable
defined in [RFC2662]. Each entry corresponds to
an ADSL alarm profile."
AUGMENTS { adslLineAlarmConfProfileEntry }
::= { adslAlarmConfProfileExtTable 1 }
adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 } AdslAlarmConfProfileExtEntry ::=
SEQUENCE {
adslAtucThreshold15MinFailedFastR Integer32,
adslAtucThreshold15MinSesL Integer32,
adslAtucThreshold15MinUasL Integer32,
adslAturThreshold15MinSesL Integer32,
adslAturThreshold15MinUasL Integer32
}
adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 } adslAtucThreshold15MinFailedFastR OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerfCurr15MinFailedFastR
reaches or exceeds this value within a given
15-minute performance data collection period,
an adslAtucFailedFastRThreshTrap notification
will be generated. The value '0' will disable
the notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 1 }
adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 } adslAtucThreshold15MinSesL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerf15MinSesL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAtucSesLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE DEFVAL { 0 }
OBJECTS { adslAtucPerfCurr15MinFailedFastR }
STATUS current
DESCRIPTION
"Failed Fast Retrains 15-minute threshold reached."
::= { adslExtAtucTrapsPrefix 1 }
adslAtucSesLThreshTrap NOTIFICATION-TYPE ::= { adslAlarmConfProfileExtEntry 2 }
OBJECTS { adslAtucPerfCurr15MinSesL }
STATUS current
DESCRIPTION
"Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAtucTrapsPrefix 2 }
adslAtucUasLThreshTrap NOTIFICATION-TYPE adslAtucThreshold15MinUasL OBJECT-TYPE
OBJECTS { adslAtucPerfCurr15MinUasL } SYNTAX Integer32(0..900)
STATUS current UNITS "seconds"
DESCRIPTION MAX-ACCESS read-create
"Unavailable seconds-line 15-minute threshold reached." STATUS current
::= { adslExtAtucTrapsPrefix 3 } DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerf15MinUasL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAtucUasLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 3 }
adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 } adslAturThreshold15MinSesL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAturPerf15MinSesL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAturSesLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 4 }
adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 } adslAturThreshold15MinUasL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAturPerf15MinUasL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAturUasLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
adslAturSesLThreshTrap NOTIFICATION-TYPE ::= { adslAlarmConfProfileExtEntry 5 }
OBJECTS { adslAturPerfCurr15MinSesL }
STATUS current
DESCRIPTION
"Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAturTrapsPrefix 1 }
adslAturUasLThreshTrap NOTIFICATION-TYPE -- definitions
OBJECTS { adslAturPerfCurr15MinUasL }
STATUS current
DESCRIPTION
"Unavailable seconds-line 15-minute threshold reached."
::= { adslExtAturTrapsPrefix 2 }
-- conformance information adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 }
adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 } adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 }
adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 } adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 }
adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 }
-- ATU-C agent compliance statements adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAtucPerfCurr15MinFailedFastR }
STATUS current
DESCRIPTION
"Failed Fast Retrains 15-minute threshold reached."
::= { adslExtAtucTrapsPrefix 1 }
adslExtLineMibAtucCompliance MODULE-COMPLIANCE adslAtucSesLThreshTrap NOTIFICATION-TYPE
STATUS current OBJECTS { adslAtucPerfCurr15MinSesL }
DESCRIPTION STATUS current
"The compliance statement for SNMP entities which DESCRIPTION
represent ADSL ATU-C interfaces." "Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAtucTrapsPrefix 2 }
MODULE -- this module adslAtucUasLThreshTrap NOTIFICATION-TYPE
MANDATORY-GROUPS OBJECTS { adslAtucPerfCurr15MinUasL }
{ STATUS current
adslExtLineGroup, DESCRIPTION
adslExtLineConfProfileControlGroup, "Unavailable seconds-line 15-minute threshold
adslExtLineAlarmConfProfileGroup reached."
} ::= { adslExtAtucTrapsPrefix 3 }
GROUP adslExtAtucPhysPerfCounterGroup adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 }
DESCRIPTION
"This group is optional. Implementations which
require continuous ATU-C physical event counters
should implement this group."
GROUP adslExtAturPhysPerfCounterGroup adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 }
DESCRIPTION
"This group is optional. Implementations which
require continuous ATU-R physical event counters
should implement this group."
GROUP adslExtNotificationsGroup adslAturSesLThreshTrap NOTIFICATION-TYPE
DESCRIPTION OBJECTS { adslAturPerfCurr15MinSesL }
"This group is optional. Implementations which STATUS current
support TCA (Threshold Crossing Alert) should DESCRIPTION
implement this group." "Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAturTrapsPrefix 1 }
OBJECT adslAtucThreshold15MinFailedFastR adslAturUasLThreshTrap NOTIFICATION-TYPE
MIN-ACCESS read-write OBJECTS { adslAturPerfCurr15MinUasL }
DESCRIPTION STATUS current
"Read-write access is applicable only when DESCRIPTION
static profiles as defined in ADSL Line MIB "Unavailable seconds-line 15-minute threshold
[RFC2662] are implemented." reached."
::= { adslExtAturTrapsPrefix 2 }
OBJECT adslAtucThreshold15MinSesL -- conformance information
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAtucThreshold15MinUasL adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 }
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAturThreshold15MinSesL adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 }
MIN-ACCESS read-write adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 }
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAturThreshold15MinUasL -- ATU-C agent compliance statements
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslLineConfProfileDualLite adslExtLineMibAtucCompliance MODULE-COMPLIANCE
MIN-ACCESS read-only STATUS current
DESCRIPTION DESCRIPTION
"Read-only access is applicable only when "The compliance statement for SNMP entities which
static profiles as defined in ADSL Line MIB represent ADSL ATU-C interfaces."
[RFC2662] are implemented."
::= { adslExtCompliances 1 } MODULE -- this module
MANDATORY-GROUPS
{
adslExtLineGroup,
adslExtLineConfProfileControlGroup,
adslExtLineAlarmConfProfileGroup
}
-- units of conformance GROUP adslExtAtucPhysPerfCounterGroup
adslExtLineGroup OBJECT-GROUP DESCRIPTION
OBJECTS { "This group is optional. Implementations which
adslLineConfProfileDualLite, require continuous ATU-C physical event counters
adslLineTransAtucCap, should implement this group."
adslLineTransAtucConfig,
adslLineTransAtucActual,
adslLineGlitePowerState
}
STATUS current
DESCRIPTION
"A collection of objects providing extended
configuration information about an ADSL Line."
::= { adslExtGroups 1 }
adslExtAtucPhysPerfCounterGroup OBJECT-GROUP GROUP adslExtAturPhysPerfCounterGroup
OBJECTS { DESCRIPTION
adslAtucPerfStatFastR, "This group is optional. Implementations which
adslAtucPerfStatFailedFastR, require continuous ATU-R physical event counters
adslAtucPerfCurr15MinFastR, should implement this group."
adslAtucPerfCurr15MinFailedFastR,
adslAtucPerfCurr1DayFastR,
adslAtucPerfCurr1DayFailedFastR,
adslAtucPerfPrev1DayFastR,
adslAtucPerfPrev1DayFailedFastR,
adslAtucPerfStatSesL,
adslAtucPerfStatUasL,
adslAtucPerfCurr15MinSesL,
adslAtucPerfCurr15MinUasL,
adslAtucPerfCurr1DaySesL,
adslAtucPerfCurr1DayUasL,
adslAtucPerfPrev1DaySesL,
adslAtucPerfPrev1DayUasL,
adslAtucIntervalFastR,
adslAtucIntervalFailedFastR,
adslAtucIntervalSesL,
adslAtucIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 2 }
adslExtAturPhysPerfCounterGroup OBJECT-GROUP GROUP adslExtNotificationsGroup
OBJECTS { DESCRIPTION
adslAturPerfStatSesL, "This group is optional. Implementations which
adslAturPerfStatUasL, support TCA (Threshold Crossing Alert) should
adslAturPerfCurr15MinSesL, implement this group."
adslAturPerfCurr15MinUasL,
adslAturPerfCurr1DaySesL,
adslAturPerfCurr1DayUasL,
adslAturPerfPrev1DaySesL,
adslAturPerfPrev1DayUasL,
adslAturIntervalSesL, adslAturIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 3 }
adslExtLineConfProfileControlGroup OBJECT-GROUP OBJECT adslAtucThreshold15MinFailedFastR
OBJECTS { MIN-ACCESS read-write
adslConfProfileLineType DESCRIPTION
} "Read-write access is applicable only when
STATUS current static profiles as defined in ADSL Line MIB
DESCRIPTION [RFC2662] are implemented."
"A collection of objects providing profile
control for the ADSL system."
::= { adslExtGroups 4 }
adslExtLineAlarmConfProfileGroup OBJECT-GROUP OBJECT adslAtucThreshold15MinSesL
OBJECTS { MIN-ACCESS read-write
adslAtucThreshold15MinFailedFastR, DESCRIPTION
adslAtucThreshold15MinSesL, "Read-write access is applicable only when
adslAtucThreshold15MinUasL, static profiles as defined in ADSL Line MIB
adslAturThreshold15MinSesL, [RFC2662] are implemented."
adslAturThreshold15MinUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing alarm profile
control for the ADSL system."
::= { adslExtGroups 5 }
adslExtNotificationsGroup NOTIFICATION-GROUP OBJECT adslAtucThreshold15MinUasL
NOTIFICATIONS { MIN-ACCESS read-write
adslAtucFailedFastRThreshTrap, DESCRIPTION
adslAtucSesLThreshTrap, "Read-write access is applicable only when
adslAtucUasLThreshTrap, static profiles as defined in ADSL Line MIB
adslAturSesLThreshTrap, [RFC2662] are implemented."
adslAturUasLThreshTrap
}
STATUS current
DESCRIPTION
"The collection of ADSL extension notifications."
::= { adslExtGroups 6 }
END OBJECT adslAturThreshold15MinSesL
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
7. Acknowledgments OBJECT adslAturThreshold15MinUasL
This document is a product of the ADSL MIB Working Group. MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
8. References OBJECT adslLineConfProfileDualLite
MIN-ACCESS read-only
DESCRIPTION
"Read-only access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
8.1 Normative References ::= { adslExtCompliances 1 }
[ANSI T1.413] American National Standards Institute, ANSI T1.413, -- units of conformance
Issue 2, "Standards Project for Interfaces Relating adslExtLineGroup OBJECT-GROUP
to Carrier to Customer Connection of ADSL Equipment", OBJECTS {
1998. adslLineConfProfileDualLite,
adslLineTransAtucCap,
adslLineTransAtucConfig,
adslLineTransAtucActual,
adslLineGlitePowerState
}
STATUS current
DESCRIPTION
"A collection of objects providing extended
configuration information about an ADSL Line."
::= { adslExtGroups 1 }
[ETSI DTS/TM06006] European Telecommunications Standards Institute adslExtAtucPhysPerfCounterGroup OBJECT-GROUP
"ADSL European Specific Requirements", November OBJECTS {
2000. adslAtucPerfStatFastR,
adslAtucPerfStatFailedFastR,
adslAtucPerfCurr15MinFastR,
adslAtucPerfCurr15MinFailedFastR,
adslAtucPerfCurr1DayFastR,
adslAtucPerfCurr1DayFailedFastR,
adslAtucPerfPrev1DayFastR,
adslAtucPerfPrev1DayFailedFastR,
adslAtucPerfStatSesL,
adslAtucPerfStatUasL,
adslAtucPerfCurr15MinSesL,
adslAtucPerfCurr15MinUasL,
adslAtucPerfCurr1DaySesL,
adslAtucPerfCurr1DayUasL,
adslAtucPerfPrev1DaySesL,
adslAtucPerfPrev1DayUasL,
adslAtucIntervalFastR,
adslAtucIntervalFailedFastR,
adslAtucIntervalSesL,
adslAtucIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 2 }
[ITU G.992.1] ITU-T Telecommunication Standardization Sector, adslExtAturPhysPerfCounterGroup OBJECT-GROUP
"Asymmetric digital subscriber line (ADSL) OBJECTS {
transceivers", June 1999. adslAturPerfStatSesL,
adslAturPerfStatUasL,
adslAturPerfCurr15MinSesL,
adslAturPerfCurr15MinUasL,
adslAturPerfCurr1DaySesL,
adslAturPerfCurr1DayUasL,
adslAturPerfPrev1DaySesL,
adslAturPerfPrev1DayUasL,
adslAturIntervalSesL, adslAturIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 3 }
[ITU G.992.2] ITU-T Telecommunication Standardization Sector, adslExtLineConfProfileControlGroup OBJECT-GROUP
"Splitterless asymmetric digital subscriber line OBJECTS {
(ADSL) transceivers", June 1999. adslConfProfileLineType
}
STATUS current
DESCRIPTION
"A collection of objects providing profile
control for the ADSL system."
::= { adslExtGroups 4 }
[ITU G.997.1] ITU-T Telecommunication Standardization Sector, adslExtLineAlarmConfProfileGroup OBJECT-GROUP
"Physical Layer Management of Digital Subscriber OBJECTS {
Transceivers", June 1999. adslAtucThreshold15MinFailedFastR,
adslAtucThreshold15MinSesL,
adslAtucThreshold15MinUasL,
adslAturThreshold15MinSesL,
adslAturThreshold15MinUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing alarm profile
control for the ADSL system."
::= { adslExtGroups 5 }
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, adslExtNotificationsGroup NOTIFICATION-GROUP
"Protocol Operations for Version 2 of the Simple Network NOTIFICATIONS {
Management Protocol (SNMPv2)", RFC 1905, January 1996. adslAtucFailedFastRThreshTrap,
adslAtucSesLThreshTrap,
adslAtucUasLThreshTrap,
adslAturSesLThreshTrap,
adslAturUasLThreshTrap
}
STATUS current
DESCRIPTION
"The collection of ADSL extension notifications."
::= { adslExtGroups 6 }
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, END
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2026] Bradner S., "The Internet Standards Process - 7. Acknowledgments
Revision 3", October 1996.
[RFC2028] Hovey R., S. Bradner, "The Organizations Involved in This document is a product of the ADSL MIB Working Group.
the IETF Standards Process", October 1996.
[RFC2493] K. Tesink "Textual Conventions for MIB Modules Using 8. References
Performance History Based on 15 Minute Intervals"
RFC 2493, January 1999.
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An 8.1 Normative References
Architecture for Describing SNMP Management Frameworks",
RFC 2571, April 1999.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, [ANSI T1.413] American National Standards Institute, ANSI
"Message Processing and Dispatching for the Simple T1.413, Issue 2, "Standards Project for Interfaces
Network Management Protocol (SNMP)", RFC 2572, April 1999. Relating to Carrier to Customer Connection of ADSL
Equipment", 1998.
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 [ETSI DTS/TM06006] European Telecommunications Standards Institute
Applications", RFC 2573, April 1999. "ADSL European Specific Requirements", November
2000.
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model [ITU G.992.1] ITU-T Telecommunication Standardization Sector,
(USM) for version 3 of the Simple Network Management "Asymmetric digital subscriber line (ADSL)
Protocol (SNMPv3)", RFC 2574, April 1999. transceivers", June 1999.
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based [ITU G.992.2] ITU-T Telecommunication Standardization Sector,
Access Control Model (VACM) for the Simple Network "Splitterless asymmetric digital subscriber line
Management Protocol (SNMP)", RFC 2575, April 1999. (ADSL) transceivers", June 1999.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [ITU G.997.1] ITU-T Telecommunication Standardization Sector,
Rose, M., and S. Waldbusser, "Structure of Management "Physical Layer Management of Digital Subscriber
Information Version 2 (SMIv2)", STD 58, RFC 2578, April Transceivers", June 1999.
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [RFC2026] Bradner S., "The Internet Standards Process -
Rose, M., and S. Waldbusser, "Textual Conventions for Revision 3", BCP 9, RFC 2026, October 1996.
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [RFC2028] Hovey R. and S. Bradner, "The Organizations
Rose, M., and S. Waldbusser, "Conformance Statements for Involved in the IETF Standards Process", BCP 11,
SMIv2", STD 58, RFC 2580, April 1999. RFC 2028, October 1996.
[RFC2662] Bathrick, G. and F. Ly "Definitions of Managed Objects for [RFC2493] Tesink, K., "Textual Conventions for MIB Modules
the ADSL Lines", May 1999. Using Performance History Based on 15 Minute
Intervals" RFC 2493, January 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
MIB", RFC 2863, June 2000. Case, J., Rose, M. and S. Waldbusser, "Structure
of Management Information Version 2 (SMIv2)", STD
58, RFC 2578, April 1999.
8.2 Informative References [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M. and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
"Simple Network Management Protocol", STD 15, RFC 1157, Case, J., Rose, M. and S. Waldbusser, "Conformance
May 1990. Statements for SMIv2", STD 58, RFC 2580, April
1999.
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart, [RFC2662] Bathrick, G. and F. Ly, "Definitions of Managed
"Introduction to Version 3 of the Internet-standard Objects for the ADSL Lines", RFC 2662, May 1999.
Network Management Framework", RFC 2570, April 1999.
[RFC1155] Rose, M., and K. McCloghrie, "Structure and [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces
Identification of Management Information for Group MIB", RFC 2863, June 2000.
TCP/IP-based Internets", STD 16, RFC 1155, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions", [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security
STD 16, RFC 1212, March 1991. Model (USM) for version 3 of the Simple Network
Management Protocol (SNMPv3)", STD 62, RFC 3414,
December 2002.
[RFC1215] M. Rose, "A Convention for Defining Traps for use with [RFC3415] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-
the SNMP", RFC 1215, March 1991. based Access Control Model (VACM) for the Simple
Network Management Protocol (SNMP)", STD 62, RFC
3415, December 2002.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, 8.2 Informative References
"Introduction to Community-based SNMPv2", RFC 1901,
January 1996.
11. Security Considerations [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
The following security matters should be considered when implementing 9. Security Considerations
this MIB.
1) Blocking unauthorized access to the ADSL MIB via the element The following security matters should be considered when implementing
management system is outside the scope of this document. It should be this MIB.
noted that access to the MIB permits the unauthorized entity to
modify the profiles (section 6.4) such that both subscriber service
and network operations can be interfered with. Subscriber service can
be altered by modifying any of a number of service characteristics
such as rate partitioning and maximum transmission rates. Network
operations can be impacted by modification of notification thresholds
such as Signal-to-Noise Ratio (SNR) margins.
2) SNMPv1 by itself is such an insecure environment. Even if the 1) Blocking unauthorized access to the ADSL MIB via the element
network itself is secure (for example by using IPSec), even then, management system is outside the scope of this document. It
there is no control as to who on the secure network is allowed to should be noted that access to the MIB permits the unauthorized
access and GET (read) the objects in this MIB. It is recommended entity to modify the profiles (section 6.4) such that both
that the implementors consider the security features as provided by subscriber service and network operations can be interfered with.
the SNMPv3 framework. Specifically, the use of the User-based
Security Model RFC 2574 [21] and the View-based Access Control Model
RFC 2575 [23] is recommended.
It is then a customer/user responsibility to ensure that the SNMP Subscriber service can be altered by modifying any of a number of
entity giving access to an instance of this MIB, is properly service characteristics such as rate partitioning and maximum
configured to give access to those objects only to those principals transmission rates. Network operations can be impacted by
(users) that have legitimate rights to access them. modifying notification thresholds such as Signal-to-Noise Ratio
(SNR) margins.
3) The profile mechanism presented in this document requires specific 2) SNMPv1 by itself is such an insecure environment. Even if the
attention. The implementor of this MIB has a choice of implementing network itself is secure (for example by using IPSec), there is no
either 'static' or 'dynamic' profiles. This decision must be control over who on the secure network is allowed to access and
consistent with the implementation of RFC 2662. GET (read) the objects in this MIB. It is recommended that the
implementors consider the security features as provided by the
SNMPv3 framework. Specifically, the use of the User-based
Security Model STD 62, RFC 3414 [RFC3414] and the View-based
Access Control Model STD 62, RFC 3415 [RFC3415] is recommended.
In the case of 'static' profiles, the elements of the profile are It is then a customer/user responsibility to ensure that the SNMP
read-write as opposed to read-create when 'dynamic' profiles are entity giving access to an instance of this MIB, is properly
implemented: configured to give access to only those objects, and to those
principals (users) that have legitimate rights to access them.
- adslConfProfileLineType, 3) The profile mechanism presented in this document requires specific
- adslAtucThreshold15MinFailedFastR, attention. The implementor of this MIB has a choice of
- adslAtucThreshold15MinSesL, implementing either 'static' or 'dynamic' profiles. This decision
- adslAtucThreshold15MinUasL, must be consistent with the implementation of RFC 2662.
- adslAturThreshold15MinSesL, and
- adslAturThreshold15MinUasL.
This decision also impacts the mechanics of the index, In the case of 'static' profiles, the elements of the profile are
adslLineConfProfileDualLite. When 'static' profiles are implemented, read-write, as opposed to read-create when 'dynamic' profiles are
its value is algorithmically set by the system and its value is implemented:
based on the ifIndex, hence not guaranteed across system reboots.
Similar to the handling of adslLineConfProfile [RFC2662], the
implementor of this MIB must ensure that the profile object values
associated with these indices are maintained across system reboots.
In the case of dynamic profiles, this object is set by the SNMP - adslConfProfileLineType,
manager. The implementor of this MIB may want to provide view of the - adslAtucThreshold15MinFailedFastR,
profile on a customer-by-customer standpoint, but should be cautious - adslAtucThreshold15MinSesL,
of the dynamic nature of these objects. - adslAtucThreshold15MinUasL,
- adslAturThreshold15MinSesL, and
- adslAturThreshold15MinUasL.
4) ADSL layer connectivity from the ATU-R will permit the subscriber This decision also impacts the mechanics of the index,
to manipulate both the ADSL link directly and the ADSL overhead adslLineConfProfileDualLite. When 'static' profiles are
control channel(AOC)/embedded operations channel (EOC) implemented, its value is algorithmically set by the system and
for their own loop. For example, unchecked or unfiltered its value is based on the ifIndex. Hence it is not guaranteed
fluctuations initiated by the subscriber could generate sufficient across system reboots. Similar to the handling of
notifications to potentially overwhelm either the management adslLineConfProfile [RFC2662], the implementor of this MIB must
interface to the network or the element manager. Other attacks ensure that the profile object values associated with these
affecting the ATU-R portions of the MIB may also be possible. indices are maintained across system reboots.
12. Intellectual Property Notice In the case of dynamic profiles, this object is set by the SNMP
manager. The implementor of this MIB may want to provide a view
of the profile on a customer-by-customer standpoint, but should be
cautious of the dynamic nature of these objects.
The IETF takes no position regarding the validity or scope of any 4) ADSL layer connectivity from the ATU-R will permit the
intellectual property or other rights that might be claimed to subscriber to manipulate both the ADSL link directly and the ADSL
pertain to the implementation or use of the technology described in overhead control channel(AOC)/embedded operations channel (EOC)
this document or the extent to which any license under such rights for their own loop. For example, unchecked or unfiltered
might or might not be available; neither does it represent that it fluctuations initiated by the subscriber could generate sufficient
has made any effort to identify any such rights. Information on the notifications to potentially overwhelm either the management
IETF's procedures with respect to rights in standards-track and interface to the network or the element manager. Other attacks
standards-related documentation can be found in BCP-11 [RFC2028]. affecting the ATU-R portions of the MIB may also be possible.
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementors or users of this
specification can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any 10. Intellectual Property Notice
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
13. Authors' Addresses The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11 [RFC2028].
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementors or users of this
specification can be obtained from the IETF Secretariat.
Faye Ly The IETF invites any interested party to bring to its attention any
Pedestal Networks copyrights, patents or patent applications, or other proprietary
3045 Park Boulevard rights that may cover technology that may be required to practice
Palo Alto, CA 94306, USA this standard. Please address the information to the IETF Executive
Director.
Phone: +1 650-475-1274 11. Authors' Addresses
Fax: +1 650-688-3119
EMail: faye@pedestalnetworks.com
Gregory Bathrick Faye Ly
NOKIA High Speed Access Nodes Pedestal Networks
1310 Redwood Way, 6503 Dumbarton Circle,
Petaluma, CA 94954, USA Fremont, CA 94555
Phone: +1 707-793-7030 Phone: +1 510-578-0158
Fax: +1 707-792-0850 Fax: +1 510-744-5152
EMail: greg.bathrick@nokia.com EMail: faye@pedestalnetworks.com
14. Full Copyright Statement Gregory Bathrick
Nokia Networks
2235 Mercury Way,
Santa Rosa, CA 95405
Copyright (C) The Internet Society (2002). All Rights Reserved. Phone: +1 707-362-1125
Fax: +1 707-535-7300
EMail: greg.bathrick@nokia.com
This document and translations of it may be copied and furnished to 12. Full Copyright Statement
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be Copyright (C) The Internet Society (2002). All Rights Reserved.
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and translations of it may be copied and furnished to
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING others, and derivative works that comment on or otherwise explain it
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING or assist in its implementation may be prepared, copied, published
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION and distributed, in whole or in part, without restriction of any
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF kind, provided that the above copyright notice and this paragraph are
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
Acknowledgement The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
Funding for the RFC Editor function is currently provided by the This document and the information contained herein is provided on an
Internet Society. "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Table of Contents Acknowledgement
1. Status of this Memo ..................................... 1 Funding for the RFC Editor function is currently provided by the
2. Abstract ............................................... 1 Internet Society.
3. The SNMP Network Management Framework ................... 1
4. Introduction ............................................ 2
5. Relationship of ADSL LINE EXTENSION MIB with standard MIBs. 3
6. Conventions used in the MIB ............................. 3
7. Conformance and Compliance .............................. 5
8. Definitions ............................................. 5
9. Acknowledgments ......................................... 25
10. References .............................................. 26
11. Security Considerations ................................. 27
12. Intellectual Property Notice .............................. 27
13. Authors' Addresses ...................................... 28
14. Full Copyright Statement ............................... 29
 End of changes. 215 change blocks. 
1399 lines changed or deleted 1353 lines changed or added

This html diff was produced by rfcdiff 1.41. The latest version is available from http://tools.ietf.org/tools/rfcdiff/